Abstract:Stacking fault energy (SFE) can play a crucial role in plastic deformation and damage mechanisms of face-centered cubic (fcc) metals. This study mainly summarized the following results: (1) With the reduction of SFE, the slip mode of fcc metals gradually changes from a facile cross-slip wavy mode to a planar mode until deformation twinning occurs; (2) The concept of effective SFE is applied to investigate the variation of SFE with dislocation density in the fcc metals, with the increase in dislocation density, the effective SFE increases; (3) The reduction of SFE is not the only factor determining the formation of deformation twins in fcc metals. In terms of calculating the competition between simulated slipping and twinning using the first principles, the critical criterion for forming deformation twinning in fcc metals was established; (4) The fatigue dislocation configuration of high-, medium-, and low-SFE fcc metals were analyzed and the judgment conditions for forming regular persistent slip bands (PSBs) are proposed; (5) With the increase in Al content, the SFE of Cu-Al alloy decreases, resulting in a simultaneous increasing trend in the tensile strength and the uniform elongation due to the increasing planar slip degree; (6) The exponential strain-hardening model can accurately describe the tensile strain-hardening process of Cu-Al alloys. The quantitative relationship among yield strength, tensile strength, and uniform elongation of Cu-Al alloy with different alloy compositions and microstructure states was successfully predicted; (7) With the increase in Al content, the fatigue strength of Cu-Al alloy is improved. Increasing Al content at the same strain amplitude will enhance its low-cycle fatigue life. Based on the experimental results above, it is shown that the alloy composition affects the deformation and damage mechanisms, and the evolution process of microscopic defects (dislocations, twins) in fcc metals and alloys. Thus, it drastically affects the tensile and fatigue properties of the fcc metals and alloys. These results provide experimental evidence and a theoretical basis for improving the mechanical properties and service reliability of fcc metals and alloys via alloy designing.

Deformation Properties of Austenitic Stainless Steels with Different Stacking Fault Energies

Effect of Temperature on the Stacking Fault Energy and Deformation Behaviour in 316L Austenitic Stainless Steel

Stacking Fault Energies in Austenitic Stainless Steels

Deformation Microstructure and Deformation-Induced Martensite in Austenitic Fe-Cr-Ni Alloys Depending on Stacking Fault Energy

Effect of Stacking Fault Energy and Austenite Strengthening on Martensitic Transformation in Fe-Mn-Si Alloys

Effects of Stacking Fault Energy on the Deformation Mechanisms and Mechanical Properties of Face-Centered Cubic Metals

Can experiment determine the stacking fault energy of metastable alloys?

Insights into plastic deformation mechanisms of austenitic steels by coupling generalized stacking fault energy and semi-discrete variational Peierls-Nabarro model

Stacking fault energy prediction for austenitic steels: thermodynamic modeling vs. machine learning

On the Stacking Fault Energy Evaluation and Deformation Mechanism of Sanicro-28 Super-Austenitic Stainless Steel

Stacking Fault Energy Determination in Fe-Mn-Al-C Austenitic Steels by X-ray Diffraction

Towards stacking fault energy engineering in FCC high entropy alloys

Effective Stacking Fault Energy in Face-Centered Cubic Metals

Effect of interstitial-driven lattice expansion on the stacking fault energy in austenitic steels

The effect of stacking fault energy on the formation of nano twin/HCP during deformation in FCC concentrated solid solution (CSS) alloys

Stacking Fault Energy Analyses of Additively Manufactured Stainless Steel 316L and CrCoNi Medium Entropy Alloy Using In Situ Neutron Diffraction

Reconciling experimental and theoretical stacking fault energies in<i> face</i><i>-centered</i><i> cubic</i> materials with the experimental twinning stress

Stacking fault energy of face-centered cubic metals: thermodynamic and ab initio approaches

Predicting the Stacking Fault Energy of Austenitic Fe-Mn-Al (si) Alloys

Effects of stacking fault energy on the deformation behavior of CoNiCrFeMn high-entropy alloys: A molecular dynamics study

Stacking Fault Energy of Face-Centered-cubic High Entropy Alloys