Abstract:<p>Microstructural and textural characteristics of Zr702 and Zr-2.5Nb alloys before and after rolling (50% reduction in thickness) were characterized and compared by employing electron channel contrast imaging and electron backscatter diffraction techniques, with underlying reasons for the differences between them explored. Results show that the starting microstructure of the Zr702 is mainly comprised of well-equiaxed α-Zr grains while the Zr-2.5Nb presents a typical dual-phase microstructure featured by bulk α grains enclosed by thin β-Zr films. After the 50% rolling, plastic deformation readily occurs through the active operation of prismatic and pyramidal slip in both the Zr alloys. Most grains are found to be elongated along rolling direction with a few less-deformed grains also present (more evident in the rolled Zr702). The β-Zr preexisting in Zr-2.5Nb alloy is softer than α-Zr and could thus be deformed more easily, allowing fewer plastic strains to be accommodated by the α grains. The starting Zr702 has a typical bimodal basal texture that is essentially unchanged after the 50% rolling. The majority of grains in the starting Zr-2.5Nb show scattered orientations with their c-axes away from normal directions (ND). After the same rolling, however, c-axes of most α-grains in the Zr-2.5Nb alloy are aligned to be close to transverse direction or ~30° from the ND (ring-like distribution), different from that of the Zr702. It is demonstrated that the formation of such textural features is related to the preexisting thin β films in the Zr-2.5Nb alloy, in addition to the slip deformation.</p>

New Orientations Between Β′2 Phase and Α Matrix in a Mg-Zn-Mn Alloy Processed by High Strain Rate Rolling

Structural relationships among monoclinic and hexagonal phases and transition structures in Mg-Zn-Y alloys

Microstructures evolution, texture characteristics and mechanical properties of Mg-2.5Nd-0.5Zn-0.5Zr alloy during the high strain rate hot-rolling

Orientation relationships between icosahedral clusters in hexagonal MgZn2 and monoclinic Mg4Zn7 phases in Mg-Zn(-Y) alloys

Oriented Nucleation Causing Unusual Texture Transition During Static Recrystallization Annealing in Cold-Rolled Mg–Zn–Gd Alloys

Evolution Of Microstructure And Local Crystallographic Orientations In Rolled Al-1%Mn Single Crystals Of {001}< 110 > Orientation

Crystal structure and stability of phases in Mg-Zn alloys: A comprehensive first-principles study

Evolution of microstructure and local crystallographic orientations in rolled Al 1% Mn single crystals of {l_brace} 0 0 1 {r_brace}< 1 1 0> orientation

Insights into the evolution of texture and mechanical properties during warm rolling and annealing of Mg–2Zn-0.5Ca alloy

Microstructural and textural differences between rolled Zr702 and Zr-2.5Nb alloys: The role played by preexisting β phase

Orientations of Nuclei During Static Recrystallization in a Cold-Rolled Mg-Zn-Gd Alloy

Deformation mechanism, orientation evolution and mechanical properties of annealed cross-rolled Mg-Zn-Zr-Y-Gd sheet during tension

Formation of Unusual Rolling Texture in a Mg-Al-Mn Alloy Sheet by Large-Strain Hot-Rolling

On the Strengthening Precipitate Phases and Phase Transformation of Β″/β′ in a Mg-Sm-Zr Alloy

Rolling Temperature and Subsequent Annealing on Microstructure, Texture and Mechanical Properties of Consecutive Rolled Mg-2.0zn-0.8gd Alloy

Origin of Extension Twinning-Mediated Static Recrystallization and Unique Parallel Alignment of (0001) Poles to Transverse Direction in Mg-3Al-0.4Mn (mass%) Alloy Sheet

Twins, shear bands and recrystallization of a Mg–2.0%Zn–0.8%Gd alloy during rolling

Microstructures and mechanical properties of Ti-55511 alloy subjected to rolling in the α+β dual-phase region

Microstructure, texture evolution and mechanical anisotropy of Mg-Gd-Y-Zn-Zr alloy sheets produced by unidirectional and cross rolling

Evolution of Deformation Substructure and MgxZnyCaz Metastable Phase in Fine-Grained Mg Alloys

Microstructural Evolution and Mechanical Properties in Zr705 During the Rolling Process