Abstract:Microstructure and texture evolution of β-quenched Zr-xNb-0.4Mo (x = 0, 0.4, 0.6 and 1.0 wt %) alloys during the cold rolling process were systematically investigated. The Zr-xNb-0.4Mo alloys exhibit the area fractions of the martensitic structure are 33.2%, 69.4%, 100% and 100% with an increase in Nb content. Under the same rolling gap (1.2 mm), the rolling reductions are 24%, 28%, 29.7% and 30%, respectively. To understand the reason for the gradual increase of rolling reductions until approximately 30%, a visco-plastic self-consistent (VPSC) model was employed to predict the texture evolution and relative activity of different deformation modes. The variation of average Schmid factors (SFs) and the variation of the relative activity of different deformation modes before and after cold rolling were calculated and compared. With the increase of Nb content, a similar variation law between the variation of average SF and the variation of relative activity was found. The basal slip in Zr-0.4Nb-0.4Mo alloy is difficult to activate due to the initial texture of Zr-0.4Nb-0.4Mo alloy. Pyramid slip can accommodate the strain along the normal direction (ND), which is beneficial to the high plasticity of Zr alloys during cold rolling. By comparing the variation of average SF of pyramid slip, it is found that the larger rolling reductions of Zr-0.6Nb-0.4Mo alloy and Zr-1.0Nb-0.4Mo alloys can be attributed to the activation of pyramid slip. The existence of primary α grains can decrease the average SF and inhibit the activation of pyramid slip. The cold rolling can make the martensite plates crushed and refined, but not to the primary α grains.

Microstructural Evolution and Mechanical Properties in Zr705 During the Rolling Process

Effect of cold rolling on microstructure and mechanical properties of pure Zr

Microstructure evolution behavior and mechanical mechanisms in a near α-Zr alloy by cold rolling

Microstructural and textural differences between rolled Zr702 and Zr-2.5Nb alloys: The role played by preexisting β phase

Texture Evolution and Temperature-Dependent Deformation Modes in Ambient- and Cryogenic-Rolled Nanolayered Zr-2.5Nb

Effects of primary α grains on rolling reductions and deformation modes in Zr alloys: Experiments and modeling

Effect of Microstructure Evolution on Mechanical Properties of a TiZrAlB Alloy Rolled by Different Processes

Effect of Zr on microstructure evolution of Ti-Mo composite microalloyed steel during rolling

Microstructure and Mechanical Properties of Annealed Mg–0.6wt%Zr Sheets by Unidirectional and Cross Rolling

Microstructures and Mechanical Properties of a Commercial Pure Zirconium during Rolling and Annealing at Different Temperatures

Effects of Rolling Reduction on Microstructural Evolution and Mechanical Properties of W-0.5wt%ZrC Alloys

Structure Evolution of Bulk Zr60Cu20Pd10Al10 Amorphous Alloy During Rolling Deformation

Microstructure Evolution and Mechanical Properties of the ZM61 Alloy Sheets under Different Pre-Rolling and High Strain Rate Rolling Temperatures

Revealing the Microstructure Evolution Mechanism and Mechanical Responses of a Novel Al–Zn–Mg–Cu Alloy by Hot Deformation Process

Effect of annealing on microstructure and hardness of hot and cold rolled Zr705

Evolution of microstructure and mechanical properties influenced by nanosized precipitates during rolling deformation

Microstructure and mechanical property of Zr 65 Al 7.5 Ni 10 Cu 12.5 Ag 5 bulk metallic glass subjected to rolling

Effect of strain rate on microstructure evolutions and mechanical properties of cryorolled Zr upon annealing

Microstructure evolution and mechanical properties of in-situ ZrB2/Al7085 nanocomposites during hot rolling deformation

Evolution of Shear Bands in the Structure of a Zirconium-Based Amorphous Alloy during Rolling at Different Temperatures

Microstructure Evolution and Recrystallization Behavior of Cold-Rolled Zr?1Sn?0.3Nb?0.3Fe?0.1Cr Alloy During Annealing