Abstract:The basal texture of traditional magnesium alloy AZ31 is easy to form and exhibits poor plasticity at room temperature. To address these problems, a multi-micro-alloyed high-plasticity Mg–1.8Zn–0.8Gd–0.1Ca–0.2Mn (wt%) alloy was developed using the unique role of rare earth and Ca solute atoms. In addition, the influence of the annealing process on the grain size, second phase, texture, and mechanical properties of the warm-rolled sheet at room temperature was analyzed with the goal of developing high-plasticity magnesium alloy sheets and obtaining optimal thermal-mechanical treatment parameters. The results show that the annealing temperature has a significant effect on the microstructure and properties due to the low alloying content: there are small amounts of larger-sized block and long string phases along the rolling direction (RD), as well as several spherical and rodlike particle phases inside the grains. With increasing annealing temperature, the grain size decreases and then increases, and the morphology, number, and size of the second phase also change correspondingly. The particle phase within the grains vanishes at 450°C, and the grain size increases sharply. In the full recrystallization stage at 300–350°C, the optimum strength-plasticity comprehensive mechanical properties are presented, with yield strengths of 182.1 and 176.9 MPa, tensile strengths of 271.1 and 275.8 MPa in the RD and transverse direction (TD), and elongation values of 27.4% and 32.3%, respectively. Moreover, there are still some larger-sized phases in the alloy that influence its mechanical properties, which offers room for improvement.

Effect of strain rate on microstructure evolutions and mechanical properties of cryorolled Zr upon annealing

Effect of cold rolling on microstructure and mechanical properties of pure Zr

Mechanical properties and thermal stability of gradient structured Zr via cyclic skin-pass cryorolling

Microstructures and Mechanical Properties of a Commercial Pure Zirconium during Rolling and Annealing at Different Temperatures

Effect of cryogenic rolling on the microstructure and texture of CuCrZr alloy

Effect of heating rate on the recrystallization behavior and mechanical properties of a cold-rolled Zr702

Microstructure evolution behavior and mechanical mechanisms in a near α-Zr alloy by cold rolling

Effect of Zr on microstructure evolution of Ti-Mo composite microalloyed steel during rolling

Cryorolling impacts on microstructure and mechanical properties of AISI 316 LN austenitic stainless steel

Effect of elevated-temperature annealing on microstructureand properties of Cu−0.15Zr alloy

Recrystallization behavior and texture evolution during annealing of cryogenic-rolled 3003 aluminum alloy

Microstructure and properties evolution of Mg–2Y–0.6Nd–0.6Zr alloy rolled at room and liquid nitrogen temperature

The Effect of Cooling Rate on Microstructure and Mechanical Properties of the Zr-4Hf-3Nb (wt%) Alloy

Effect of Deformation on Precipitation and the Microstructure Evolution during Multistep Thermomechanical Processing of Al-Zn-Mg-Cu Alloy

Effect of heat treatment on the microstructure and mechanical properties of cryogenic rolling 2195 Al–Cu–Li alloy

Effect of strain rate on microstructure and mechanical properties of spray-formed Al–Cu–Mg alloy

Effect of annealing treatment on the microstructure and mechanical properties of warm-rolled Mg–Zn–Gd–Ca–Mn alloys

Effects of annealing treatment on mechanical properties of 8011 aluminum alloy after cryogenic rolling

Work Hardening Behavior and Microstructure Evolution of a Cu-Ti-Cr-Mg Alloy during Room Temperature and Cryogenic Rolling

Effect of cryogenic rolling and multistage thermo-mechanical treatment on the microstructure and properties of the Cu-0.4Cr-0.39Zn-0.1Mg-0.07Zr alloy

Microstructure evolution and recrystallization of Ti6246 alloy in hot‐rolling and annealing processes