Abstract:Al-Si alloys offer distinctive advantages including light weight, high strength, and excellent formability. These attributes enable the production of large, thin-walled complex castings under low-pressure die casting, which is pivotal for vehicle lightweighting. However, the casting process of these alloys is susceptible to defects, and their performance is intricately linked to their microstructure. Recognizing the deep-seated connection between process, structure, and performance is of immense academic and engineering value. In this work, by integrating the thermodynamics, kinetics, and multi-component phase diagram database, we formulated an improved cellular automata (ICA) model. Relying on cooling curves and solidification microstructures at varied positions of the step casting, we established an equiaxed crystal nucleation model apt for the low-pressure casting of the Al-7Si- x Mg alloy. Subsequent three-dimensional simulations of the microstructural evolution during this alloy’s low-pressure casting solidification mirrored experimental observations, particularly concerning dendrite morphology. Experiments on low-pressure casting of step-shaped components were conducted. The ICA model accurately depicted α-Al dendrites and the cooling rate’s impact on nucleation density and dendrite size uniformity in the ternary Al-7Si- x Mg alloy. Our simulation results demonstrated a remarkable consistency with experimental data. Further, we provided a comprehensive analysis of the relationship between secondary dendrite arm spacing and cooling rate. The precision of the ICA model, when assessing dendrite tip growth rate, was corroborated by juxtaposing it with the Lipton–Glicksman–Kurz (LGK) analytical model. This work provides theoretical guidance for the establishment of a quantitative relationship of solidification-microstructure-properties within the framework of integrated computational materials engineering.

Morphology Evolution of Primary Mg2Si in Al–20Mg2Si–0.1Ca Alloys Prepared with Various Solidification Cooling Rates

Investigation on morphology of primary Mg2Si in Al-20wt.%Mg2Si composite with experiment and first-principle calculations

One-Step Synthesis of Spherical Primary Mg2Si in Ca/Sb-Modified Al-Mg2Si Alloy

Relationship between Microstructure Evolution and Tensile Properties of AlSi10Mg Alloys with Varying Mg Content and Solidification Cooling Rates

Dendritic Si growth morphologies in highly undercooled Al-Si alloys

Microstructure control and performance evolution of hypereutectic Al–20Mg2Si alloy by novel Al–Ca–Sb master alloy

Phase Selection and Morphological Evolution for a Dilute Al-Mg-Si Alloy Under Sub-Rapid Solidification

Effect of Cooling Rate on Solidification Parameters and Microstructure of Al-7Si-0.3Mg-0.15Fe Alloy

Calculation Based on the Formation of Mg2Si and Its Effect on the Microstructure and Properties of Al–Si Alloys

Numerical Simulation of Solidified Microstructure of Ternary Al-Si-Mg Alloy Using an Improved Cellular Automaton Method

Morphology evolution of β-phase in Al-Mg-Si alloys during aging treatment

Effect of Ca Addition on Solidification Microstructure of Hypoeutectic Al-Si Casting Alloys

Microstructural Evolution of Al-Si Alloy above Liquidus Temperature during Holding Temperature

Effect of Al2Ca Addition and Heat Treatment on the Microstructure Modification and Tensile Properties of Hypo-Eutectic Al–Mg–Si Alloys

Characterization of Refining the Morphology of Al–Fe–Si in A380 Aluminum Alloy due to Ca Addition

Formation of Phases and Microstructures in Al-8Si Alloys with Different Mg Content

Effect of compression ratio on microstructure evolution of Mg–10%Al–1%Zn–1%Si alloy prepared by SIMA process

Alloying effect of Mg on microstructure and mechanical properties at 300 °C of Al–5Cu–1Mn–0.5Ni heat-resistant alloy

Stabilizing Al–Mg–Si–Cu alloy by precipitation nano-phase control

Formation of intermetallic phases during solidification in Al-Mg-Mn 5xxx alloys with various Mg levels

Hot deformation behaviour and microstructure evolution of Al-3%Mg2Si alloy