Abstract:A near-eutectic Al-Mg 2 Si-Mg alloy with high strength and toughness has been developed by adding 1.2-3.6 wt.% excess Mg (ΔMg) into Al-10Mg 2 Si alloy and systematically investigating the influences of ΔMg on the changes in the proportion of phases, microstructure characteristics, defect susceptibility, tensile properties, and fracture behavior of the alloy. The results indicate that with adding ΔMg content from 1.2 to 3.6 wt.%, the microstructure of the Al-10Mg 2 Si alloy transformed from hypoeutectic, near eutectic, then to hypereutectic characteristics. Moreover, the size of primary α-Al dendrites and SDAS values decrease accordingly as the ΔMg content increases from 0 to 2.8 wt.%. Furthermore, the addition of ΔMg could effectively refine the eutectic Mg 2 Si phase and change its 3D morphology from a clustered radial long plate-like bundle structure to a fine strip-like one. As a result, the strength and plasticity of the alloys have been significantly improved simultaneously. Among them, Al-10wt.%Mg 2 Si-2.8wt.%Mg near-eutectic alloy has the highest tensile properties, with YS, UTS, and EL values reaching 322.03 MPa, 117.42 MPa and 7.8%, which are 38.6%, 13.5% and 188.9% higher than the ΔMg-free alloy, respectively. Additionally, the addition of ΔMg resulted in the transitions of the solidification and tensile fracture mode of the alloys. The brittleness of Al-10wt.%Mg 2 Si alloy comes from the decohesion of coarse eutectic Mg 2 Si particles in the early stage of stretching, while the large amount of plastic deformation generated before the cracking of fine eutectic Mg 2 Si particles is responsible for the high strength and ductility of the Al-10wt.%Mg 2 Si-2.8wt.%Mg alloy. Furthermore, the preparation of the near-eutectic alloy will provide a reference for the development of other eutectic aluminum alloys with high strength and toughness for gravity casting.

Microstructure control and performance evolution of hypereutectic Al–20Mg2Si alloy by novel Al–Ca–Sb master alloy

Effect of Al2Ca Addition and Heat Treatment on the Microstructure Modification and Tensile Properties of Hypo-Eutectic Al–Mg–Si Alloys

Study on the Effect of Pre-Refinement and Heat Treatment on the Microstructure and Properties of Hypoeutectic Al-Si-Mg Alloy

Microstructural refinement and tensile properties enhancement of Al-10Mg2Si cast alloys by copper addition

The Effect of Solution Treatment on the Si Particles’ Morphology Evolution and the Thermal Conductivity and Tensile Properties of Sb-Modified Al-8Si-0.6Mg Alloys

Effects of Si Content and the Addition Amount of Al-3b Master Alloy on the Solidification Structures of Hypoeutectic Al-Si Alloys

Solidification microstructure manipulation mechanism of hypoeutectic and hypereutectic Al-Si alloys controlled by trace in-situ nano-Fe 2 B and nano-Fe 3 Si

Synergistic Effect of Sc and Excess Mg on the Microstructure and Mechanical Properties of Hypoeutectic Al-10Mg2Si Alloy

Microscopic mechanism of mechanical property improvement of the casted Al-7Si-0.4Mg-0.3Y alloy

Development of Al–Nb–B master alloy with high Nb/B ratio for grain refinement of hypoeutectic Al–Si cast alloys

Microstructure and properties evolution of Al–17Si–2Fe alloys with addition of quasicrystal Al–Mn–Ti master alloy

Effect of Mg addition on microstructure and mechanical properties of Al-Si-Cu-Fe alloy with squeeze casting

Modification mechanism and tensile property of Al-9Si-0.4Mg-0.1Cu alloy

Effect of beryllium addition and heat treatment on the microstructure and mechanical properties of the 15%Mg2Si/Al-8Si composite

Investigation on Microstructures and Mechanical Properties of the Hypoeutectic Al-10Si-0.8Fe- X Er Alloy

The Effect of Si Content on the Microstructure and Mechanical Properties of Al–1.2Mg–xSi–1.2Cu–0.6Mn Cast Alloy

Microstructure and mechanical properties of Si micro-alloyed (Ti28Zr40Al20Nb12)100-xSix (x=0, 0.1, 0.2, 0.5) high entropy alloys

Effect of Ca Addition on Solidification Microstructure of Hypoeutectic Al-Si Casting Alloys

Development of a Near Eutectic Al-Mg2Si-Mg Alloy with High Strength and Toughness

Calculation Based on the Formation of Mg2Si and Its Effect on the Microstructure and Properties of Al–Si Alloys

Sn-Sc microalloying-induced property improvement and micromechanisms of an Al-Mg-Si alloy