Abstract:The microstructure evolution and mechanical properties of Al–3.92Cu–1.10Li–0.68Mg–0.32Ag–0.23Mn–0.35Zn–0.11Zr and Al–3.92Cu–1.12Li–0.76Mg–0.29Ag–0.24Mn–0.24Zn–0.12Zr–0.083Sc (wt%) alloys during homogenization with different cooling modes were comprehensively studied. It was clearly revealed that the minor Sc addition refined the grains of as-cast Al–Cu–Li–Mg alloys through the formation of primary Al3(Sc, Zr) phases during the solidification process, and induced Sc enrichment in the θ (Al2Cu) eutectic. After the homogenization treatment, the majority of coarse nonequilibrium eutectic phases at the grain boundaries dissolved into the α-Al matrix, leading to the relatively uniform distribution of each element. Sc-added alloy after homogenization treatments possessed more superior strength and ductility than Sc-free alloy. Compared to the furnace cooling mode, the air cooling mode could inhibit the precipitation of micron-sized coarse T1 (Al2CuLi) phase and improve the mechanical properties of the alloys. After homogenization, the continuous Al2Cu phase in the as-cast Sc-added alloy dissolved and transformed to an array of W-(Al, Cu, Sc) ternary phase, which was identified as Al6Cu6Sc with the body-centered tetragonal structure. The appearance of spherical Al6Cu6Sc particle could not damage the mechanical properties of Al–Cu–Li–Mg alloys after the homogenization treatment. The tensile strength, yield strength and elongation of Sc-added alloy after the homogenization by air cooling were 390 MPa, 265 MPa and 10.8%, respectively. The investigation of Al6Cu6Sc phase offered a potential avenue to produce high-quality Sc-added 2xxx series alloys.Graphic

Sn-Sc microalloying-induced property improvement and micromechanisms of an Al-Mg-Si alloy

Developing a high-performance Al–Mg–Si–Sn–Sc alloy for essential room-temperature storage after quenching: aging regime design and micromechanisms

Influence of the interaction between Si and Sc on the microstructure and tensile properties of as casted Al-Si-Sc alloys

The microstructure and property of Al–Si alloy improved by the Sc-microalloying and Y 2 O 3 nano-particles

Effect of Scandium on Grain refinement mechanism and Mechanical Properties of Al-7Si-0.6Mg alloy at Different Cooling Rates

Nano-phase transformation of composite precipitates in multicomponent Al-Mg-Si(-Sc) alloys

Microstructures evolution and mechanical properties disparity in 2070 Al-Li alloy with minor Sc addition

Improving the Mechanical Properties and Intergranular Corrosion Resistance of Al-9.2Mg-0.8Mn-0.2Zr Alloy by Sn Addition

The role of Sn element on the deformation mechanism and precipitation behavior of the Al–Cu–Mg alloy

Study on Sc Microalloying and Strengthening Mechanism of Al-Mg Alloy

Effects of Cu Addition on the Microstructure and Properties of the Al–Mn–Fe–Si Alloy

Effect of a Trace Addition of Sn on the Aging Behavior of Al–Mg–Si Alloy with a Different Mg/Si Ratio

EFFECT OF Sc ON MICROSTRUCTURE AND PROPERTIES OF Al-Li-Cu-Mg-Zr ALLOY

Microstructure evolution, mechanical property response and strengthening mechanism induced by compositional effects in Al–6 Mg alloys

Effect of Minor Sc Addition on the Microstructure Evolution of Al–Cu–Li–Mg Alloy During Homogenization with Different Cooling Modes

Effect of Sn contents on natural aging and precipitation hardening in Al-Mg-Si alloys

Improving mechanical properties of Mg-Sn alloys by co-addition of Li and Al

The Effects of Silicon Addition on the Microstructure and Mechanical Properties of a Mg-Al-Sn Alloy Produced by Vacuum Assisted High Pressure Die Casting

Uncovering the combining V with Ni micro-addition alloying on the mechanical properties and multiphase transformation during solidification and homogenization of Al–Zn–Mg–Cu–Sc alloy

Synergistic effect of Sn + Sc on high temperature strengthening in Al–5Cu heat-resistant alloy

Enhanced Mechanical Properties and Isotropy of Mg-2Al-0.8Sn Alloy through Ca Addition