Abstract:In this paper, the effect of Si content on the microstructure and mechanical properties of the Al–1.2Mg– x Si–1.2Cu–0.6Mn cast alloy was investigated. The study aimed to explore the optimal addition of Si element to improve the comprehensive properties of alloys. The microstructure, phase composition and fracture morphology of the alloy were determined through OM, SEM, EBSD and XRD analysis. The Si content in the alloy ranged from 0.48 to 2.4 wt.%. With the increase of Si content, the number of strengthening phases increases, which improves the comprehensive properties of the alloy. When the Si content is 0.8 wt.%, the eutectic Mg 2 Si transforms from rod-shaped to larger block shaped, and the formation of coarse Mg 2 Si phase limits the elongation of the alloy. When the Si content is 2.4 wt.%, fine Al 2 Cu phases are present in this alloy and coexist with Al(Fe,Mn)Si phases, while an increase in the Si content appears as partially accompanied by an incipient crystalline Si phase around the Al(Fe,Mn)Si phase. The alloy exhibits a maximum tensile strength, yield strength and elongation of 198.2 MPa, 101.2 MPa and 4.96%, respectively, with a hardness of 80.94 Hv. It consists of five alloy phases, mainly α-Al, Mg 2 Si, Al(Fe, Mn)Si eutectic phase, Q-AlCuMgSi eutectic phase and the beginning crystalline silicon phase formed due to the increased Si content. The Si content can improve alloy strength, but there is some damage to the toughness of the alloy. Higher silicon alloy content results in the formation of fine Al 2 Cu eutectic. This result makes it possible to achieve a higher level of strength with a reduced loss of ductility in the alloy.

The Effects of Silicon Addition on the Microstructure and Mechanical Properties of a Mg-Al-Sn Alloy Produced by Vacuum Assisted High Pressure Die Casting

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Enhanced Mechanical Properties and Isotropy of Mg-2Al-0.8Sn Alloy through Ca Addition

Effect of Sn Addition on the Microstructure and Mechanical Properties of AZ31 Alloys

Influence of Al Addition on the Microstructure and Mechanical Properties of Mg-Zn-Sn-Mn-Ca Alloys

Effect of silicon addition on microstructure and mechanical properties of a high strength Ti-4Al-4Mo-4Sn alloy prepared by powder metallurgy

Sn-Sc microalloying-induced property improvement and micromechanisms of an Al-Mg-Si alloy

Effect of Ca addition on microstructure and mechanical properties of Mg–3.8Al–1.1Sn alloys

Disclosing Differential Precipitation Behavior of a Novel High Mg-containing Al-Mg-Zn-Si Alloy

Influence of Si Addition on the Microstructure and Mechanical Behaviour of Mg-5Sn-3Zn-1Mn Alloy

Enhancement of Hardening and Thermal Resistance of Mg–Sn-based Alloys by Addition of Cu and Al

The Effect of Si Content on the Microstructure and Mechanical Properties of Al–1.2Mg–xSi–1.2Cu–0.6Mn Cast Alloy

Effect of a Trace Addition of Sn on the Aging Behavior of Al–Mg–Si Alloy with a Different Mg/Si Ratio

Effects of Adding Trace Modification Elements and Heat Treatment on the Strength and Toughness of AlSi8Cu2MgMn Alloy

Effect of Sn contents on natural aging and precipitation hardening in Al-Mg-Si alloys

Effect of Minor Elements Content on the Phase Formation and Mechanical Properties of 6xxx Series Aluminum Alloy Sheets

Effects of Sn and Mn Addition on the Microstructure and Mechanical Properties of As-Extruded Mg–2Al–1Zn Alloys

Effect of Sn addition on age-hardening and precipitation behavior of Al-Mg-Si alloys with different Mg/Si ratios

Improving mechanical properties of Mg-Sn alloys by co-addition of Li and Al

Effects of Mg2Sn precipitation on the age-hardening and deformation behaviour of a Mg-Sn-Al-Zn alloy

Effect of Mg2sn Intermetallic on the Grain Refinement in As-Cast Am Series Alloy