Abstract:The impact of minor Mg addition on microstructure and mechanical properties of cast Al–Li–Cu–Zr alloy with high lithium content (3 wt % Li) were studied to understand a qualitative assessment of sequence and kinetics of multiple precipitations and its effect on mechanical properties. Scanning Electron Microscope and X-ray diffraction results suggested that raising the content of Mg gradually altered the grain structure of the as-cast alloys and increased the types and volume fraction of the grain boundary intermetallic phase. Unusually, solvus temperature is higher than solidus temperature in 0.5 Mg alloy (Al–3Li–2Cu-0.5Mg-0.15Zr, wt. %), resulting in the incipient melting of the matrix before the complete dissolution of the intermetallic phases. Prominent enhancements in both age-hardening and precipitation kinetics of the base alloy with the addition of Mg were also easily identified, indicating the important role of Mg during isothermal aging. Transmission Electron Microscope and atom probe tomography results showed that minor Mg addition (0.2 wt %, denoted by 0.2 Mg alloy) could encourage the diffusion of Cu atoms by the aggregation of Mg–Cu-vacancy co-clusters, thereby promoting the nucleation of the T1-Al2CuLi and θ′-Al2Cu precipitates. In addition, S′-Al2CuMg precipitate was therefore introduced as a result of Mg addition. With further increasing the content of Mg to 0.5 wt %, the nucleation and growth of S′ precipitate would be promoted at the expense of T1 and θ′ precipitates, especially the latter. Based on the theoretical models and regression analysis, the formation mechanism of δ′-Al3Li precipitate-free-zones gradually changed from the initial vacancy-depletion mechanism to the solute-depletion mechanism, and Mg element could significantly inhibit the coarsening of δ′ precipitate-free-zones. The best balance between ductility and strength was obtained by 0.2 Mg alloy aged for 32 h, and the alloys have significant advantages in terms of density (2.437 g/cm3) and elastic modulus (82.65 GPa) over conventional cast aluminum alloys (density: 2.7–2.8 g/cm3; elastic modulus: 72 GPa).

Effect of Minor Elements Content on the Phase Formation and Mechanical Properties of 6xxx Series Aluminum Alloy Sheets

The Effect of Si Content on the Microstructure and Mechanical Properties of Al–1.2Mg–xSi–1.2Cu–0.6Mn Cast Alloy

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

The effect of Zn content on the microstructure and mechanical properties of the Al-mg-Si alloy

Disclosing Differential Precipitation Behavior of a Novel High Mg-containing Al-Mg-Zn-Si Alloy

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

Effects of Al Concentration on Microstructure and Mechanical Properties of Mg-xAl-1Zn-1Si Alloy

Effect of Mischmetal Addition on Microstructure and Mechanical Properties of As-Cast and As-Rolled Mg–Sn–Ca Alloys

Effect of Mn content on microstructure and properties of 6000 series aluminum alloy

Influence of Al Addition on the Microstructure and Mechanical Properties of Mg-Zn-Sn-Mn-Ca Alloys

Effects of Mg content on microstructure and mechanical properties of low Zn-containing Al−xMg−3Zn−1Cu cast alloys

Effects of Li Content on Phase Evolution and Mechanical Properties of Mg-xLi-6Zn-1.5Y Alloy

Alloying effect of Mg on microstructure and mechanical properties at 300 °C of Al–5Cu–1Mn–0.5Ni heat-resistant alloy

Effect of Fe and Mn Content on the Microstructures and Tensile Behaviour of AlSi7Cu3 Alloy: Thermal Analysis and Tensile Tests

The Effects of Silicon Addition on the Microstructure and Mechanical Properties of a Mg-Al-Sn Alloy Produced by Vacuum Assisted High Pressure Die Casting

Effect of Al on the Microstructure and Mechanical Properties of Mg–Sn–Ca–Mn Wrought Alloy

Significant roles of minor Mg addition in microstructural evolution and mechanical properties of cast Al–3Li–2Cu-0.15Zr alloy

Study on properties and precipitation behavior of 6000 series alloys with high Mg/Si ratios and Cu contents

Effects of Different Zn/Mg Ratio and Ti Content on Hot Extruded 7xxx series Aluminum Alloy

Effect of Sn content on microstructure and tensile properties of as-cast and as-extruded Mg−8Li−3Al−(1,2,3)Sn alloys

Effect of Sm content on microstructure and properties of extruded Mg-6Al-2Sr alloy