Abstract:Samples with different amounts of TiC (2, 3.5, and 5 wt%) are analyzed in a hot stage microscope, capturing the softening and melting temperatures. It is found that the presence of TiC elevates the melting initiation temperature above the melting point of pure iron. Observed TiC precipitates have to distinct morphologies: primary blocky/cubic and secondary eutectic plate like. The remelting of Fe‐xTiC metal matrix composites (MMCs) is studied using the sessile drop method. This is to determine the conditions needed for the complete dissolution of TiC precipitates in the Fe‐based melt. Samples with different amounts of TiC (2, 3.5, and 5 wt%) are analyzed in a hot‐stage microscope (HSM), capturing the softening and melting temperatures. A Cr‐alloyed steel is selected as a matrix. Consequently, the presence of TiC elevates the melting initiation temperature above the melting point of pure iron (e.g., 1659 ± 10 °C for Fe‐5TiC). Furthermore, samples with higher TiC amounts exhibit higher melting initiation temperatures. This trend is confirmed by differential scanning calorimetry measurements, conducted on the representative Fe‐xTiC samples. Microstructural examinations of the solidified (HSM) samples identify two distinct TiC precipitate morphologies: primary blocky/cubic and secondary eutectic plate like. For instance, the Fe‐5TiC sample contains numerous blocky/cubic precipitates (7.5 ± 3.1 μm) clustered at the upper cross‐ section, while secondary plate‐like precipitates (20.4 ± 11.8 μm) are uniformly distributed in eutectic assemblies with the matrix. This study provides meaningful insights for optimizing the production of as‐cast and as‐atomized Fe‐TiC MMCs, particularly in selecting reinforcement levels and homogenization temperatures for complete TiC dissolution.

Thermodynamic analysis on in-situ TiC synthesis in Fe-C-Ti-Mn system

Thermodynamic Investigation on K2TiF6 and C Powder to Prepared in-situ TiCp in Molten Al-Si-Fe Alloy

Influence on TiC microstructure from different synthesis processes in the Cu–Ti–SiC system

Numerical Simulation of In Situ Reaction Synthesis of TiC-Reinforced Steels from Elemental Fe-Ti-C Powders

The microstructures of in-situ synthesized TiC by Ti-CNTs reaction in Cu melts

Effect of Ti/V Ratio on Thermodynamics and Kinetics of MC in Γ/α Matrices of Ti–V Microalloyed Steels

Study of the Synthesis Process of Non-Stoichiometric TiC in Cu-Ti Melts

Formation mechanism of Ti3AlC2 in TiO2–Al–C/TiC systems at high temperatures

In-situ Synthesis of Nanocrystalline TiC Powders, Nanorods, and Nanosheets in Molten Salt by Disproportionation Reaction of Ti(II) Species

Preparation, Microstructure and Mechanical Properties of In-Situ TiC/Al–Si–Fe Aluminum Matrix Composites

Thermodynamic analysis of thermite reactions for synthesizing Ni-based alloys

In-situ Production and Microstructure of TiC/Fe_3Al Composites

The effect of carbon source and molar ratio in Fe–Ti–C system on the microstructure and mechanical properties of in situ TiC/Fe composites

Remelting of In Situ Fe‐xTiC Metal Matrix Composites by the Sessile Drop Method: Characteristic Temperatures and Microstructural Analysis

Prediction of the Thermodynamic Stability of TiC in Ni-Al Based Alloys

Combustion Synthesis of TiC–Fe Composites under the Action of an Electric Field

In-situ formation of titanium carbide in copper-titanium-carbon system: A review

Synthesis of Ti2(In Al1-)C (x = 0–1) solid solutions with high-purity and their properties

Microstructure evolution of Fe-Ti-C system synthesized by low temperature combustion induced in electric field

Thermodynamic Analysis of the Formation Mechanism of Metastable Carbides during Tempering of Fe–C Martensite

Combustion synthesis of ternary carbide Ti3AlC2 in Ti–Al–C system