Abstract:In this study, K 2 TiF 6 and C powder (Ti:C atomic ratio 1:1) are introduced into Al-Si-Fe alloy by contact reaction method. The focus of this study is to investigate the reaction and precipitation behavior of Ti source in the alloy melt, and the effect of reaction products on the microstructure and properties of Al-Si-Fe alloy. The results show that the reaction products formed between Ti and the matrix alloy can destroy the acicular β-Fe phase in the original alloy. The transformation results in the a morphological change of the alloy from needle-like structure to Chinese script and fishbone-like structure, which effectively improves the mechanical properties of the alloy. The DSC analysis results indicate that Al-Si- Fe powder, K 2 TiF 6 powder, and C powder undergo significant exothermic reactions at around 950 °C, corresponding to the formation of TiC. Further microscopic morphology observations support the inference that TiC powders formed in this temperature range. Firstly, the synthesis of the matrix takes place at 580 °C. K 2 TiF 6 mixed with alloy powder shows an obvious exothermic peak at 660 °C, corresponding to the formation of the second phase Al 3 Ti by wetting and chemical reaction. However, it is worth noting that the reaction intermediate product(Al 4 C 3 phase) consumes three times as much Al 3 Ti as itself. As a result, the exothermic peak generated by Al 3 Ti disappears. Lastly, a long-term exothermic reaction that takes place above 850 °C lead to the gradual replacement of the Al 3 Ti phase by TiC particles. The mechanical properties test indicates that the needle-shaped Al 3 Ti to some extent deteriorates the alloy's properties. But the final product (TiC) can offset the deteriorating effect of Al 3 Ti and restore the alloy's property.

Microstructure evolution of Fe-Ti-C system synthesized by low temperature combustion induced in electric field

Combustion Synthesis of TiC–Fe Composites under the Action of an Electric Field

Combustion Synthesis of Fe-Ti-C System by Electric Field Inducement: Effect of Electric Current on the Synthesis Products

Mechanosynthesis Mechanism of Tic Powders

Effect of Pressure on Combustion Synthesis of TiC/Fe-Cu Composites under the Action of Electric Current

Formation Mechanism of Spherical TiC in Ni-Ti-C System during Combustion Synthesis

Investigation of TiC formation during ball-milling of elemental titanium and carbon

The effect of carbon source and molar ratio in Fe–Ti–C system on the microstructure and mechanical properties of in situ TiC/Fe composites

Combustion Synthesis of VC/Fe Composites under the Action of an Electric Field

Effect of Combustion Temperature on Combustion Synthesis of Ti3AlC2 and Ti2AlC

Numerical Simulation of In Situ Reaction Synthesis of TiC-Reinforced Steels from Elemental Fe-Ti-C Powders

Preparation and Sinterability of Submicron Titanium Carbide Powders Synthesized with Phenolic Resin As Carbon Source by Carbothermal Reduction

Thermodynamic Investigation on K2TiF6 and C Powder to Prepared in-situ TiCp in Molten Al-Si-Fe Alloy

Structure Formation in the Combustion Synthesis of Al2O3–TiC Composites

Influence on TiC microstructure from different synthesis processes in the Cu–Ti–SiC system

Microhardness and Microstructure of In-Situ Formed Fe-50%TiC Composites by Different Heating Methods

Investigation on microstructure of TiC-Fe cermets prepared by SHS/PHIP

Combustion synthesis of ternary carbide Ti3AlC2 in Ti–Al–C system

Study of Patterns and Mechanisms of Combustion of a Powdered and Granulated Ti–C–B System

Combinatorial synthesis of multiple Zr Ti1-C by electric field-assisted combustion synthesis

Combustion Synthesis of Tinxc1-X Powders with Ultra Fine Particle Size by Using Titanium Oxide As Dilution