Abstract:In some circumstances, hybrid polymer microfluidic chips composed of both elastic, gas-permeable polydimethylsiloxane (PDMS) and rigid plastics are needed. However, it is quite difficult to bond PDMS irreversibly to plastics such as polystyrene (PS). In this article, a facile method for irreversible bonding of PDMS to PS was proposed based on UV/O-3-assisted surface modification in combination of surface silanization. Firstly, a PS sheet was exposed to UV/O-3 to produce oxygen-containing polar moieties, such as hydroxyl and carboxylic acid, on its surface. Secondly, the UV/O-3 treated PS sheet was silanized with (3-aminopropyl)triethoxysilane (APTES) via the reaction between the oxygen-containing polar moieties on the PS surface and the molecules of APTES. Thirdly, the silanized-PS sheet and the PDMS substrate with micro channel network were treated with UV/O-3 again to generate silanol moieties on both surfaces. Finally, the UV/O-3 treated PDMS was immediately brought intimate contact with the UV/O-3 treated silanized-PS, and irreversible bonding of PDMS with PS occurred after putting the PDMS-PS complex at room temperature for 1 h through the condensation reaction between silanol moieties. Contact angle measurement, X-ray photoelectron spectroscopy, total reflection Fourier transformation infrared spectrometer were applied to characterize the surface chemistry of the PS during the UV/O-3 treatment and silanization. The hybrid PDMS-PS microfludic chips prepared with the established method can bear a gas pressure higher than 0.5 MPa and a water stream at a flow rate higher than 170 mu L/min (the test channels were 2.5 cm in the length, 50 mu m in the width, 200 mu m in the depth). A hybrid PDMS-PS microfluidic chip composed of gas-permeable PDMS substrate with channel network and excellently biocompatible PS cover sheet was fabricated for cell culture. The experimental results showed that HeLa cells cultured in the hybrid PDMS-PS microchip grew much better than those cultured in the full PS microchip, and slightly better than those in the full PDMS microchip.

High hydrosilylation efficiency of porous silicon SiH x species produced by Pt-assisted chemical etching for biochip fabrication

Biological Functionalization and Patterning of Porous Silicon Prepared by Pt-assisted Chemical Etching

Macroporous silicon templated from silicon nanocrystallite and functionalized SiH reactive group for grafting organic monolayer

An Approach for Irreversible Bonding of PDMS-PS Hybrid Microfluidic Chips at Room Temperature

Facile Preparation of Porous Silicon from Silver-Assisted Chemical Etching Method on Silicon

The Optical Properties of Porous Silicon Produced by Metal-Assisted Anodic Etching

Hydrolysis and silanization of the hydrosilicon surface of freshly prepared porous silicon by an amine catalytic reaction

Direct Imprinting of Porous Silicon Via Metal‐Assisted Chemical Etching

Optimization of Metal-Assisted Etchant Components for Fabrication of Porous Silicon

Biofunctionalisation of Porous Silicon (ps) Surfaces by Using Homobifunctional Cross-Linkers

Preparation of Large-Area Porous Silicon Through Cu-Assisted Chemical Etching

Silicon Based Solvent Immersion Imprint Lithography for Rapid Polystyrene Microfluidic Chip Prototyping

Wafer-Scale Fabrication and Transfer of Porous Silicon Films As Flexible Nanomaterials for Sensing Application

Preparation of Hydrophobic Porous Silicon by Metal-Assisted Etching with Pd-Catalyst

A Combined Etching Process Toward Robust Superhydrophobic Sic Surfaces

Mild‐Temperature Catalyzed Hydrosilylation for Simplified Carbohydrate Functionalization of Porous Silicon Nanoparticles

Morphological and Electrical Features of Porous Silicon Prepared by Metal-Induced Chemical Etching

Porous silicon-based oligonucleotide chips

Fabrication of antireflective layers on silicon using metal-assisted chemical etching with in situ deposition of silver nanoparticle catalysts

Research on Pt Nanoparticles-Assisted Chemical Etching of Heavily Doped p-Type Monocrystalline Silicon

An Improved Surface Modification of Poly(dimethylsiloxane) Via a Green Chemistry Approach for On-Chip Biomolecular Separation