Abstract:The HfOx-based resistive random access memory (RRAM) has been extensively investigated as one of the emerging nonvolatile memory (NVM) candidates due to its excellent memory performance and compatibility with CMOS process. In this study, the influences of deposition ambient, especially the oxygen partial pressure during thin film sputtering, on the resistive switching characteristics are discussed in detail for possible nonvolatile memory applications. The Ni/HfOx/TiN RRAMs are fabricated, and the HfOx films with different oxygen content are deposited by a radio frequency magnetron sputtering at room temperature under different oxygen partial pressures. The oxygen partial pressures in the sputter deposition process are 2%, 4% and 6% relative to engineer oxygen content in the HfOx film. Current-voltage (I-V) measurements, X-ray photoelectron spectroscopy, and atomic force microscopy are performed to explain the possible nature of the stable resistive switching phenomenon. Through the current-voltage measurement, typical resistive switching behavior is observed in Ni/HfOx/TiN device cells. It is found that with the increase of the oxygen partial pressure during the preparation of HfOx films, the stoichiometric ratio of O in the film is improved, the root mean square (RMS) of the surface roughness of the film slightly decreases due to the slower deposition rate under a higher oxygen partial pressure, and the high resistance state (HRS) current decreases. In addition, by controlling the oxygen content of the device, the endurance performance of the device is improved, which reaches up to 10 3 under a 6% oxygen partial pressure. The HfOx films prepared at a higher oxygen partial pressure supply enough oxygen ions to preserve the switching effect. As the oxygen partial pressure increases, the uniformity of the switching voltage is improved, which can be attributed to the fact that better oxidation prevents the point defects (oxygen vacancies) from aggregating into extended defects. Through the linear fitting and temperature test, it is found that the conduction mechanism of Ni/HfOx/TiN RRAM device cells in low resistance state is an ohmic conduction mechanism, while in high resistance state it is a Schottky emission mechanism. The interface between TE and the oxide layer (HfOx) is expected to influence the resistive switching phenomenon. The activation energy of the device is investigated based on the Arrhenius plots in HRS. A switching model is proposed according to the theory of oxygen vacancy conductive filament. Furthermore, the self-compliance behavior is found and explained.

Performance improvement after nitridation treatment in HfO2-based resistance random-access memory

Conduction Mechanism and Improved Endurance in HfO 2 -Based RRAM with Nitridation Treatment

Nitrogen-induced improvement of resistive switching uniformity in a HfO2-based RRAM device

Ti/HfO2-Based RRAM with Superior Thermal Stability Based on Self-Limited TiOx

Resistive Switching Characteristics of Pt/TaOx/HfNx Structure and Its Performance Improvement

Forming-Free HfOx-Based Resistive Memory with Improved Uniformity Achieved by the Thermal Annealing-Induced Self-Doping of Ge

Nitrogen-Oxyanion-Doped HfO2 Resistive Random-Access Memory with Chemically Enhanced Forming

Influneces of Different Oxygen Partial Pressures on Switching Properties of Ni/HfOx/TiN Resistive Switching Devices

formance of resistive switching memory with a transparent ITO electrode using supercritical fl uid nitridation

Improvement of Hafnium Oxide Resistive Memory Performance Through Low-Temperature Supercritical Oxidation Treatments

Influence of Nitrogen Buffering on Oxygen in Indium-Tin-oxide Capped Resistive Random Access Memory with NH3 Treatment

Tuning oxygen vacancies and resistive switching properties in ultra-thin HfO2 RRAM via TiN bottom electrode and interface engineering

Obtaining Lower Forming Voltage and Self-Compliance Current by Using a Nitride Gas/Indium–Tin Oxide Insulator in Resistive Random Access Memory

Boosting the Performance of Resistive Switching Memory with a Transparent ITO Electrode Using Supercritical Fluid Nitridation

HfOx Bipolar Resistive Memory with Robust Endurance Using ZrNx As Buttom Electrode

Optimization of the Forming Process of HfOx-Based RRAM to Achieve Bidirectional Forming and Enhanced Switching Performance by Inserting an Oxygen-Vacancy-Rich Layer

Improvement of HfOx-Based RRAM Device Variation by Inserting ALD TiN Buffer Layer

Endurance improvement technology with nitrogen implanted in the interface of WSiOx resistance switching device

Endurance Improvement Technology with Nitrogen Implanted in the Interface of ${\rm WSiO}_{\bf X}$ Resistance Switching Device

Improvement of Resistive Switching Uniformity in TiOx Film by Nitrogen Annealing

Improved Switching Stability in SiNx-based RRAM by Introducing Nitride Insertion Layer with High Conductivity