Abstract:Positron Annihilation Technique is very sensitive to vacancy defects and small vacancy clusters and has been used as supplementary for TEM in radiation damage research. In this paper, we evaluated the displacement damage in solids induced by positrons and its effect on defects measurement, which has not been considered carefully in most PAT application. Displacement damage could only be produced when kinetic energy of positron exceeds a threshold determined by average displacement energy and the mass of atoms. Based on the latest models of displacement damage and numerical Mott elastic differential cross section of positrons interacting with atoms, displacement cross section for fast positron in solids was calculated and compared with that for electrons. In the energy range from 1MeV to 100MeV, electrons will produce more displacement defects than positrons do, especially in high-Z materials. Number of total defects depends on the primary displacement cross section and the size of damage cascades. To get distributions of defects and terminating position of positrons in materials, a Monte Carlo tool with full damage model was developed and validated. From the results of Monte Carlo modeling, the defects -generated by mono-energy positron beam have shallower distribution than the stopping position of positrons, indicating separation of defects and positrons and this fact benefits defects measurement because displacement damage produced by fast probing positron beam have little affection on the measurement. But for the positron beams from radioactive sources (such as 22Na and 64Cu) with continuous energy spectrum (from 0 to Emax), the depth profile of defects and terminated position of positrons overlap with each other and this fact indicated that defects measurement in materials will be affected by extra defects produced by positrons. The density of defects produced by positron beam is quite low with a typical value of about 0.01∼0.1 cm-3 per positron in low-Z materials, which could be comparable with the defect density limitation if enough accumulated positrons are implanted into materials during measurement. For commonly used structural metals (such as Fe, Mn, Cu and metals with Z number higher than 40), using positron from 22N and 64Cu directly to measure defects density is quite safe because the energy is smaller than the displacement threshold.

Defect Characterization in Thermoelectric Zn-Sb Systems by Positron Annihilation

Positron lifetime calculations for defects in Zn

First-Principles Calculation of Defect Formation and Positron Annihilation States in Bi2Te3

Thermal stability of grain boundaries in nanocrystalline Zn studied by positron lifetime spectroscopy

Transient positron annihilation spectroscopy under light irradiation at liquid nitrogen temperature: evaluation of defect states in single-crystal ZnO

The Correlation Between Dislocations and Vacancy Defects Using Positron Annihilation Spectroscopy

Positron Lifetime Calculation for Possible Defects in Nanocrystalline Copper

Positron effective mass and positronium work function in ZnxCd1−xS

Systematic investigation of positron annihilation in transition metals from first principles

Defects in Proton-Irradiated Zn-Doped Gasb Studied by Positron Annihilation and Photoluminescence

Direct Control of Defects on Positron Lifetimes and Dielectric Constant of Microwave Ceramics

Vacancies tailoring lattice anharmonicity of Zintl-type thermoelectrics

Thermoelectric power factor of pure and doped ZnSb via DFT based defect calculations

Vacancy-induced pseudo-gap formation in antiferromagnetic Cr$_{0.86}$ZnSb

Perspective on defect characterization in semiconductors by positron annihilation spectroscopy

Evaluation of displacement damage in solids induced by fast positrons: Modeling and effect on vacancy measurement

Quantum Monte Carlo study of Doppler broadening of positron annihilation radiation in semiconductors and insulators

Atomic geometry and electronic structure of defects in Zn3N2

Positron Annihilation in (ga, Mn)N: A Study of Vacancy-Type Defects

Zn-Induced Defect Complexity for the High Thermoelectric Performance of n-Type PbTe Compounds

Positron-Annihilation Investigation of Defects in Hydrogen-Containing Fz Si Irradiated with High-Dose Reactor Neutrons