Abstract:Fabricating chalcopyrite Cu(In,Ga)Se2 (CIGS) films from electrodeposition is one of the most effective ways to lower the production cost and energy consumption compared with that from vacuum methods. However, this process often produces a pronounced rough surface with impurity phases, induces the accumulation of gallium, and results in a low surface band gap. In this work, ammonium sulfide ((NH4)2S, AS) solution treatment is used as a single way to realize the optimization of the distribution of elements on the CIGS surface. It is revealed that this room-temperature process not only significantly reduces the surface roughness (Ra) but also incorporates sulfur (S) into the CIGS film successfully. An appropriate AS treatment duration can effectively remove the impurity phases and reduce the series resistance, and thus the dominant recombination moves from the CdS/CIGS heterojunction interface to the bulk. Consequently, the open-circuit voltage (VOC) and fill factor (FF) of solar cells have been greatly improved (from 484 to 532 mV, from 62.52 to 68.15%), leading to higher efficiency of 11.92%. This work focuses on revealing the etching mechanism of the CIGS films by the AS treatment at room temperature.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.1c00220?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.1c00220</a>.Best solar cell parameters of different unannealing samples (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.1c00220/suppl_file/ae1c00220_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Fabrication of Homogeneous CIGS Thin Film by Plasma-Enhanced Se Vapor Selenization Coupled with Etching Process

Increasing surface band gap of Cu(In,Ga)Se2 thin films by post depositing an In-Ga-Se thin layer.

Fabrication of Cu(In,Ga)Se-2 Thin Films from Nanoparticles by Non-Vacuum Mechanochemical Method and Rapid Thermal Annealing Process

Fabricating Cu(In,Ga)Se2 (CIGS) Thin Films with Large Grains Based on the Quaternary CIGS Targets

Ga2Se3 Treatment of Cu-rich CIGS Thin Films to Fabricate Cu-poor CIGS Thin Films with Large Grains and U-shaped Ga Distribution

10.3%-Efficient Submicron-Thick Cu(In,Ga)Se2 Solar Cells with Absorber Fabricated by Sputtering In2Se3, CuGaSe2 and Cu2Se Targets

Synthesis and Characteristics of Cu(In,Ga)Se2 Thin Films from Nanoparticles by Solvothermal Method and Selenisation Process

Preparation of Cu(In,Ga)Se2 Thin Film by Solvothermal and Spin-coating Process

Preparation of Cu(In,Ga)Se2 Thin Film by Non-Vacuum Mechanochemical and Spin-Coating Process

Preparation of Cu(In,Ga)Se2 Thin Film by Sputtering from Cu(In,Ga)Se2 Quaternary Target

13.6%-Efficient Cu(In,Ga)Se-2 Solar Cell with Absorber Fabricated by Rf Sputtering of (In,ga)(2)se-3 and Cu Se Targets

Synthesis and Characterization of CIGS Powder

Characterization of Cu(In,Ga)Se2 Films Deposited by Single-Step Electron Beam Evaporation for Solar Cell Applications

Metal Precursor with Bi-Layer Indium for Cu(In,Ga)Se2 Thin Film Preparation

Study on Two-Step Process of Preparing CIGS Films

Pulse Selenization in Cu(In,Ga)Se 2 Solar Cells: A Promising Approach to Achieve High Efficiency by Electrodeposition

Gallium Diffusion in Cigs Thin Films Prepared by Sequential Sputtering/Selenization Technique

A New Simple Route to Grow Cu(In,Ga)Se2 Thin Films with Large Grains in the Co-Evaporation Process

Enhancing Surface Properties for Electrodeposited Cu(In,Ga)Se 2 Films by (NH 4 ) 2 S Solution at Room Temperature

Cu(In,Ga)Se2 solar cell with 16.7% active‐area efficiency achieved by sputtering from a quaternary target

Effect of Se Vapor Concentration on Cigs Film Preparation