Abstract:Dynamic resistance, which occurs when a HTS coated conductor carries a DC current under an AC magnetic field, can have critical implications for the design of HTS machines. Here, we report measurements of dynamic resistance in a commercially available SuperPower 4 mm-wide YBCO coated conductor, carrying a DC current under an applied AC magnetic field of arbitrary orientation. The reduced DC current, I t/I c0, ranged from 0.01 to 0.9, where I t is the DC current level and I c0 is the self-field critical current of the conductor. The field angle (the angle between the magnetic field and the normal vector of the conductor wide-face) was varied between 0° and 90° at intervals of 10°. We show that the effective width of the conductor under study is ~12% less than the physical wire width, and we attribute this difference to edge damage of the wire during or after manufacture. We then examine the measured dynamic resistance of this wire under perpendicular applied fields at very low DC current levels. In this regime we find that the threshold field, B th, of the conductor is well described by the nonlinear equation of Mikitik and Brandt. However, this model consistently underestimates the threshold field at higher current levels. As such, the dynamic resistance in a coated conductor under perpendicular magnetic fields is best described using two different equations for each of the low and high DC current regimes, respectively. At low DC currents where I t/I c0 ≤ 0.1, the nonlinear relationship of Mikitik and Brandt provides the closest agreement with experimental data. However, in the higher current regime where I t/I c0 ≥ 0.2, closer agreement is obtained using a simple linear expression which assumes a current-independent penetration field. We further show that for the conductor studied here, the measured dynamic resistance at different field angles is dominated by the perpendicular magnetic field component, with negligible contribution from the parallel component. Our findings now enable the dynamic resistance of a single conductor to be analytically determined for a very wide range of DC currents and at all applied field angles.

Winding and Testing of YBCO Coils Using Different HTS Wires

Development of a 400 M YBCO Racetrack Coil for HTS Machine Applications

Observation And Analysis Of Defects In Impregnated Ybco Racetrack Coil

Degradation-Free Impregnated YBCO Pancake Coils by Decreasing Radial Stress in the Windings and Method for Evaluating Delamination Strength of YBCO-Coated Conductors

Delamination Properties of YBCO Tapes Under Shear Stress Along the Width Direction

Winding angle optimization and testing of small-scale, non-planar, high-temperature superconducting stellarator coils

High-Performance YBCO-Coated Superconductor Wires

33.8 TESLA WITH A YBa2Cu3O7−xSUPERCONDUCTING TEST COIL

Exfoliated YBCO filaments for second-generation superconducting cable

The experimental research and analysis on the quench propagation of YBCO coated conductor and coil

Development of YBCO Insert for a 25 T All Superconducting Magnet

The study of multiple thermal cycle of HTS YBCO bulk

<i>In situ</i> detection of delamination and critical current degradation caused by the thermal stress in epoxy impregnated REBa<sub>2</sub>Cu<sub>3</sub>O<sub>7</sub>- coils

Test and Analysis of Electromagnetic and Mechanical Properties of HTS Coil During Quench State

Quench Protection of YBCO Coils: Co-Winding Detection Method and Limits to Hot-Spot Temperature

The dynamic resistance of YBCO coated conductor wire: effect of DC current magnitude and applied field orientation

Analysis of Technical Routes to Fabricate HTS Coated Conductors

Design and Test of a Double Pancake Coil for SMES Application Wound by HTS Roebel Cable

Critical Current Survival in the YBCO Superconducting Layer of a Delaminated Coated Conductor

Development of persistent joints for superconducting Bi-2212 coils

Coupling losses and transverse resistivity of multifilament YBCO coated superconductors