Abstract:<p>Herein, Ti(C,N)-based cermets prepared via mechanical activation and subsequent in situ carbothermal reduction was studied. The correlation between microstructural and mechanical performance of these cermets was investigated by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. Results indicated that with the increase in tungsten carbide (WC) content, hard particles of ceramic gradually evolved from complete solid solution to partial solid solution with a little quantity of core–rim structure. Mean particle size of the cermet first increased, and then, slightly decreased. In addition, grain shape gradually changed from relatively faceted to nearly round. Initially, with the increase in WC content, the increase in transverse rupture strength (TRS) and slight increase in hardness were related to the strengthening of both solid solution and fine grains. However, with further addition of WC, the decrease in hardness was primarily because of lower hardness of (Ti,W,Mo) (C,N) phase with higher W content. Extremely high toughness of cermets with WC content of 0 and 3 wt% was mainly due to the decrease in interface area compared to traditional cermets, which resulted in significant reduction in interfacial strain between the rim and core. Moreover, toughness improvement of cermets containing 6 to 12 wt% of WC was due to comprehensive effect of superb coherent relationship of black core/grey rim particles, semi-coherent relationship with high-density dislocations of solid-solution particles, and solid-solution strengthening of white core-grey rim particles.</p>

Core-rim Microstructure and Properties of WC/Ni Composites

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Effect of Ni Content on Microstructure and Properties of WC-Ni Composites Prepared by Electroless Plating and Powder Metallurgy

Preparation of Ultra-Fine WC-Co Cermet and Its Wear Behavior

Effects of WC content on core/rim phases and microstructure of TiB2-TiC-WC-(Co-Ni) cermets

Microstructural and Mechanical Characterization of Colloidal Processed WC/(W5Vol%Ni) via Spark Plasma Sintering

Dissolving Mechanism of the WC/W2Cp in NiCrBSi Alloy and Surface Modification for the WC/W2Cp by Carburizing

Study on the abrasive resistance of Ni-based coatings containing WC hard phase

Correlation between microstructure and mechanical properties of Ti(C,N)-xWC-Ni cermets prepared by mechanical activation and subsequent in situ carbothermal reduction

Interface microstructure and abrasive wear properties of WC-iron matrix composites with Ni, Mo, Fe added to the preforms

Effect of WC-12Co on the mechanical and wear performance of laser melting deposition nickel-based alloy

Microstructure and mechanical properties of WC reinforced 18Ni300 composites produced by selective laser melting

Microstructural evolution and performance analysis of WC-11Co reinforced iron matrix composites

Wear performance of Ni-WC composites and heat-damage behaviour of WC particle during vacuum-induction melting process

Microstructure and Mechanical Properties of Nanocrystalline Wc-Particle-Reinforced Ti-Based Composites with Nano/Ultrafine-Grained Intermetallic Matrix from Spark Plasma Sintering and Crystallization of Amorphous Phase

Enhanced Mechanical and Electrical Properties of CuCrZr-WC Alloy Prepared by Mechanical Alloying and Spark Plasma Sintering

Preparation and characterization of high-performance in-situ synthesized WC reinforced nickel-based coatings

Effect of Ni content on the microstructure and properties of WCoB-TiC cermets

Influence of Ni Content on the Structure and Mechanical Properties of Ultrafine WC-Ni-VC-TaC Hardmetals

Microstructure and properties of W Cu composites reinforced by in-situ generated WC