Abstract:Bi2Te3-based compounds are currently the most commercially relevant thermoelectric materials near room temperature. They are prepared via hot pressing, hot deformation, spark plasma sintering, and other consolidation processes, which are typically performed at 400–500 °C. Such high-temperature processes are energy-intensive and generate unnecessary waste heat, making them undesirable for a large-scale production. In this study, a low-temperature liquid-phase-assisted sintering (or so-called cold-sintering) process was employed to fabricate p-type Bi0.5Sb1.5Te3 bulk materials at temperatures below 150 °C. At the optimal sintering temperature (130 °C), a ZT value as high as 0.56 at 450 K can be achieved, competitive to that of a commercial Bi0.5Sb1.5Te3 ingot (ZT 0.8–1.0). The addition of a small amount of transient liquid facilitates grain reorientation and expedites a mass transfer process under axial compaction and liquid evaporation conditions, thus resulting in nearly fully densified Bi0.5Sb1.5Te3 pellet samples (>97% theoretical density). Furthermore, the low-temperature sintering process results in the reduction of grain size and promotes twin boundaries, resulting in a low lattice thermal conductivity of 0.57 W m–1 K–1 at 380 K due to phonon scattering. The strategy reported in this work can be used not only as a substitute for high-temperature sintering of other thermoelectric materials but also to engineer phonon scattering for high-performance thermoelectrics.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.1c03540.Single parabolic band model and calculated transport properties; EBSD analysis for pellet sintered at 110 °C; BSE, EDS mapping, and TEM images of pellet sintered at 130 °C; average ZT values; and XPS results (PDF)This article has not yet been cited by other publications.

High-performance and High-Stability Bismuth Selenide Core Thermoelectric Fibers

In4Se3 Alloy Core Thermoelectric Fibers

Microstructure and thermoelectric properties of porous Bi 2 Te 2.85 Se 0.15 bulk materials fabricated by semisolid powder processing

Enhanced Thermoelectric Properties of Polycrystalline Bi2Te3 Core Fibers with Preferentially Oriented Nanosheets

Sn-Se alloy core fibers

High-Performance n-Type Bi2Te3 Thermoelectric Fibers with Oriented Crystal Nanosheets

Bismuth Core Fibers

Antimony Selenide Core Fibers

Enhanced Thermoelectric Properties of Bi2 Te3 -Based Micro-Nano Fibers Via Thermal Drawing and Interfacial Engineering.

Enhanced Thermoelectric Properties of Bi2Te3‐based Micro‐nano Fibers Via Thermal Drawing and Interfacial Engineering

Enhanced N-Type Bismuth-Telluride-Based Thermoelectric Fibers Via Thermal Drawing and Bridgman Annealing.

Bi8Se7: Delocalized Interlayer π-Bond Interactions Enhancing Carrier Mobility and Thermoelectric Performance near Room Temperature

Thermoelectric Properties of Single Crystal EuBiSe3 Fiber

Interfacial Design Contributing to High Conversion Efficiency in Mg3(Sb, Bi)2/Bi2Te3 Thermoelectric Module with Superior Stability

Tailoring microstructure and electrical transportation through tensile stress in Bi2Te3 thermoelectric fibers

Intrinsically Low Thermal Conductivity In Bisbse3: A Promising Thermoelectric Material With Multiple Conduction Bands

Few-layer Bi2O2Se: A promising candidate for high-performance near-room-temperature thermoelectric applications

Significant Enhancement of Thermoelectric Figure of Merit in BiSbTe‐Based Composites by Incorporating Carbon Microfiber

Cold-Sintered Bi 2 Te 3 -Based Materials for Engineering Nanograined Thermoelectrics

Realizing High Thermoelectric Properties in Bi2S3 Bulk via Band Engineering and Nanorods Compositing

Isovalent co-alloying contributes to considerable improvement in thermoelectric performance of BiSe bulks with weak anisotropy