Abstract:Despite zirconia (ZrO2) ceramics and lithium disilicate (Li2Si2O5) glass-ceramics have been widely applied on the market for dental restorations, composites that can combine the advantages of both are still demanded. Here we introduced a ZrO2-Li2Si2O5 ceramic with minimized glass phases that fabricated through a sol-gel method and subsequent pressureless sintering. ZrO2-Li2Si2O5 powders were obtained after the gel precursors were heat treated under 800 °C. The gel-derived powders were molded and pressureless sintered under 900-1000 °C to investigate their sintering properties. From the microstructures of the sintered samples, we knew that the densification process was dominated by the growth of Li2Si2O5 grains instead of the growth of ZrO2 grains. Increasing in Li2Si2O5 content can promote ceramic densification. Interestingly, reactions between ZrO2 and Li2Si2O5 were observed with sintering temperature higher than 916 °C, which can increase the porosity of the ceramics. Therefore, both the content of Li2Si2O5 and sintering temperature should be well adjusted to achieve samples with desired properties. Finally, ceramics with flexural strength of 226 MPa and porosity of 0.4% were achieved from powders with moderate Li2Si2O5 content after sintering at 1000 °C.

Preparation of Highly Porous ZrB2/ZrC/SiC Composite Monoliths Using Liquid Precursors Via Direct Drying Process

Synthesis of Monolithic Zirconia with Macroporous Bicontinuous Structure Via Epoxide-Driven Sol–gel Process Accompanied by Phase Separation

Preparation of Hierarchical Porous Silicon Carbide Monoliths via Ambient Pressure Drying Sol–Gel Process Followed by High-Temperature Pyrolysis

Preparation and properties of high-porosity ZrB2-SiC ceramics by water-based freeze casting

Preparation of macroporous zirconia monoliths from ionic precursors via an epoxide-mediated sol-gel process accompanied by phase separation

Fabrication of ZrB 2 -Sic Ceramic Composites by Optimized Gel-Casting Method

Preparation of Li-doped ZrO2 Porous Monoliths via Sol-Gel Process Accompanied by Phase Separation

Preparation of macroporous Li2ZrO3 monoliths via an epoxide-mediated sol–gel process accompanied by phase separation

Carbothermal synthesis of zirconium carbide hollow microspheres from polyzirconoxane and phenolic resin by spray drying

Preparation of Macroporous Zirconia Monoliths via Sol-Gel Process Accompanied by Phase Separation

Microstructure and phase evolution behavior of SiZrBC ceramic precursors synthesized via sol–gel method

Effects of Zr on the Precursor Architecture and High-Temperature Nanostructure Evolution of Sioc Polymer-Derived Ceramics

In-situ synthesis of hierarchically high porosity ZrB 2 ceramics from carbon aerogel template with excellent performance in thermal insulation and light absorption

Preparation of Porous Spodumene/zircon Composite Ceramics and Its Thermal and Mechanical Properties

Sol-gel preparation of ZrO2–Li2Si2O5 ceramics and their sintering properties

Preparation and Mechanism of Interconnected Mesoporous Carbon Monoliths from Phenolic Resin/Ethylene Glycol Mixtures

Preparation and stereolithography 3D printing of ultralight and ultrastrong ZrOC porous ceramics

Synthesis of high-temperature resistant monolithic zirconia-based aerogel via facile water glass assisted sol–gel method

Fabrication and microstructure evolution of Csf/ZrB2-SiC composites via direct ink writing and reactive melt infiltration

Porous Yttria‐stabilized Zirconia Ceramics Fabricated by Nonaqueous‐Based Gelcasting Process with PMMA Microsphere As Pore‐Forming Agent

Monolithic ZrB 2 ‐based UHTC s using polymer‐derived Si(Zr,B)CN as sintering aid