Abstract:Dense and enhanced mechanical properties (Zr, Ti)(C, N)-based composites were fabricated using ZrC, TiC0.5N0.5, and Si powders as the raw powders by reactive hot-pressing at 1500–1700 °C. At the low sintering temperature, both (Zr, Ti)(C, N) and (Ti, Zr)(C, N) solid solutions were formed in the composites by adjusting the ratio of ZrC to TiC0.5N0.5. During the sintering process, the Si added at a rate of 5 mol% reacted with ZrC and TiC0.5N0.5 to generate SiC. With the increase in Si addition, it was found that the residual β-ZrSi was formed, which greatly reduced the flexural strength of composites but improved their toughness. The reaction and solid-solution-driven inter-diffusion processes enhanced mass transfer and promote densification. The solid solution strengthening and grain refinement improved the mechanical properties. The ZrC–47.5 mol% TiC0.5N0.5–5 mol% Si (raw powder) composite possessed excellent comprehensive performance. Its flexural strength, Vickers hardness, and fracture toughness were 508 ± 33 MPa, 24.5 ± 0.7 GPa, and 3.8 ± 0.1 MPa·m1/2, respectively. These reached or exceeded the performance of most (Zr, Ti)(C, N) ceramics reported in previous studies. The lattice distortion, abundant grain boundaries, and fine-grained microstructure may make it possible for the material to be resistant to radiation.

Fabrication of ZrB 2 -Sic Ceramic Composites by Optimized Gel-Casting Method

Effects of SiC Platelet and ZrSi2 Additive on Sintering and Mechanical Properties of ZrB2-based Ceramics by Hot-Pressing

Preparation and properties of high-porosity ZrB2-SiC ceramics by water-based freeze casting

Processing and Mechanical Properties of Zirconium Diboride‐Based Ceramics Prepared by Spark Plasma Sintering

Fabrication of (SiC-AlN)/ZrB2 Composite with Nano-Micron Hybrid Microstructure via PCS-Derived Ceramics Route

Processing, microstructure, and mechanical properties of chopped SiC fibers reinforced ZrB2–hBN–based composites

Preparation and Mechanical Properties of ZrB2-based Ceramics Using MoSi2 As Sintering Aids

Pressureless Sintering of Silicon Carbide Ceramics Containing Zirconium Diboride

Colloid and Rheological Property of the Concentrated SiC/Si Suspensions

Fabrication and microstructure evolution of Csf/ZrB2-SiC composites via direct ink writing and reactive melt infiltration

Fabrication, Microstructural Evolution, and Mechanical Properties of SiC/(Hf0.25Ta0.25Zr0.25Nb0.25)C/C Nanocomposites

Fabrication, Structure and Properties of Porous SiC Ceramics with High Porosity and High Strength

Effect of sintering temperature and holding time on the microstructure and mechanical properties of ZrB2–SiCw composites

The Fabrication and Mechanical Properties of SiC/ZrB2 Laminated Ceramic Composite Prepared by Spark Plasma Sintering

Mechanical Properties of Short Carbon Fiber Reinforced ZrB2–SiC Ceramic Matrix Composites

Study on gelcasting and properties of recrystallized silicon carbide

Mechanical Properties of ZrB<sub>2</sub>-Based Ceramics Reinforced by Nano-SiC Whiskers

Fabrication and mechanical properties of ZrB2–SiCw ceramic matrix composite

Microstructures and Enhanced Mechanical Properties of (Zr, Ti)(C, N)-Based Nanocomposites Fabricated by Reactive Hot-Pressing at Low Temperature

The Fabrication of ZrO2–ZrC Microspheres by Internal Gelation and Carbothermal Reduction Process

Fabrication and Properties of Short Carbon Fiber-ZrB2 Ceramic Matrix Composites