Abstract:The dense WC-M2 high-speed steel matrix composites (WC-M2 HSS MMCs) with different WC content were prepared by mechanical alloying and vacuum sintering process. Tungsten Carbide (WC) with 0, 2, 5, 8, and 10 (by weight %) were dispersed in the matrix. The effects of WC content on the densification mechanism, phase composition, microstructure, fracture morphology, and mechanical and wear properties of the sintered composites were systematically investigated. The experimental results showed that at a vacuum sintering temperature of 1260 °C, the composite material specimens achieved near-full densification, with predominant phases being Martensitic, M 7 C 3 , M 6 C, M 2 C, MC, WC, α-Fe, and γ-Fe. Reasonable WC addition has improved grain uniformity and reduced micro-defects, which enhanced the overall mechanical properties. With an increase in WC content, the hardness and relative density of the composites showed a gradual increase, whereas transverse rupture strength and impact toughness initially improved but subsequently decreased. The friction coefficient displayed an initial increase followed by a decrease, while the wear rate showed an opposite trend. The impact fracture morphology is dominated by the interfacial separation between the WC particle phase and the binder phase, supplemented by the plastic tearing of the binder phase. The impact toughness mainly depended on the fracture of the binder phase. During crack propagation, both intergranular and transgranular fractures exist, of which the intergranular fracture prevails and coarse grains are more prone to transgranular fracture. With 5 wt.% WC, the steel matrix composites obtained peak mechanical performance, with impact toughness, bending strength, and hardness measuring 13.2 J cm −2 , 1584.3 MPa, and 780.9 HV, respectively, which also yielded the highest wear resistance.

Fracture Toughness of Tungsten Carbide Reinforced Fe-Matrix Surface Composites

Nanostructured Diamond-Tic Composites with High Fracture Toughness

Fracture behavior of cemented carbides with CoNiFe medium entropy alloy binder

Effect of Tungsten Carbide Additions on the Microstructure, Mechanical, and Tribological Properties of M2 High-Speed Steel Matrix Composites

Fracture behaviour, microstructure, and performance of various layered-structured Al2O3-TiC-WC-Co composites

Microstructure and mechanical properties of tungsten fiber reinforced tungsten composites prepared by Fe activated sintering

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

Microstructural evolution and performance analysis of WC-11Co reinforced iron matrix composites

High temperature fracture mechanism of ultrafine WC-Co cemented carbides containing (Ti,W)C

Strength improvement and fracture mechanism in Fe40Al/TiC composites with high content of TiC

Micro-Mechanical Fracture Investigations on Grain Size Tailored Tungsten-Copper Nanocomposites

Insight into the Microstructure and Tensile Behavior of the W–Cu Composite Reinforced with Tungsten Fibers and Particulates

Adaptation of Fracture Mechanics Methods for Quality Assessment of Tungsten Carbide Cutting Inserts

Study of Microstructure of Coarse-grain Tungsten Carbide Composite Produced by In-Situ Metallurgy Reaction

Microstructural evolution and toughening mechanism of WC-Co composite prepared by amorphous-crystallization method

Fracture Behavior of Cu/Cu–WCP Layered Composites

Interfacial Microstructure and Mechanical Property of the Discontinuous Short Tungsten Fiber-Reinforced Tungsten Matrix Composites

Microstructure and mechanical properties of WC reinforced 18Ni300 composites produced by selective laser melting

R-curve Behavior of TiC Particle Reinforced Al2O3 Composites

Interfacial Bonding And Abrasive Wear Behavior Of Iron Matrix Composite Reinforced By Ceramic Particles

Microstructure Evolution and Hardness Improvement of WC-Co Composites Sintered with Fe Substituting Part of Co Binder