Abstract:Transition metal boride enable applications in fields of cutting tools as the hard phase, but their fabrication suffers from shortcomings in high temperature for binary and hard/soft phase balance. Here, we leveraged a WCoB-Co cermets prepared by using elemental powders of W, Co and B powders via in situ synthesis method and investigated the microstructure evolution of a composite structure of WCoB/Co. The phase evolution, microstructure evolution and mechanical properties were investigated using X-ray diffraction (XRD), differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and energy dispersive spectrometer (EDS). The complete sintering process consist of three solid-phase reaction stages and one liquid-phase sintering stage. The solid-phase reaction stage includes the following three reactions: B + 2Co → Co2B, 11 W +15 Co2B → 9WCoB + W2Co21B6, and 14 W + 2W2Co21B6 → 12WCoB + 23Co + Co7W6. The eutectic liquid phase, essential for the densification, forms at 1323 °C. The Rockwell hardness and density value reach 87.5HRA and 12.11 g/cm3, respectively. At 1380 °C, the traverse rupture strength (TRS) reaches the peak value of 1495 MPa. Moreover, the results show that transgranular fracture is the main fracture mode. The densification stage was completed at ~1400 °C. In particular, Co7W6 phase was discovered during the study of the evolution of WCoB-Co cermets. An increase of the B content was found to be beneficial to eliminate the Co7W6 phase that proved to be detrimental to mechanical properties.

Study of Microstructure of Coarse-grain Tungsten Carbide Composite Produced by In-Situ Metallurgy Reaction

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Microstructural Characterization of Nanostructured WC-Co Cemented Carbides

Microstructure and properties of W Cu composites reinforced by in-situ generated WC

Microstructure Evolution and In-Situ-formed Mechanism of Dual-Scale WC-Fe Reinforced Iron Matrix Composites

Fe–W–C Thermodynamics and in Situ Preparation of Tungsten Carbide-Reinforced Iron-Based Surface Composites by Solid-Phase Diffusion

Microstructure Evolution in the Cemented Carbides Wc-Coi. Effect of the C/W Ratio on the Morphology and Defects of the Wc Grains

Investigation on Microstructure and Fracture of WC Particles Reinforced Steel Matrix Composites by Electroslag Melting and Casting

Study on Effect of High-Entropy Alloy Binder on Microstructure and Properties of WC Cemented Carbide Doped with Rare Earth Oxide

A Novel Approach of In-Situ Synthesis of WC Particulate-Reinforced Fe-30Ni Ceramic Metal Coating

Investigation on Microstructure and Mechanism of In-situ Producing Grey Cast Iron Matrix Composite

Microstructure and Tribology Behaviors of In-Situ WC/Fe Carbide Coating Fabricated by Plasma Transferred Arc Metallurgic Reaction

Microstructural and Mechanical Properties of in Situ WC-Fe/Fe Composites

Microstructure and Formation Mechanism of WC Coating on Tungsten Fabricated by Interstitial Carburization: A Multiscale Investigation

Microstructure and Fracture Toughness of a WC-Fe Cemented Carbide Layer Produced by a Diffusion-Controlled Reaction

Study of carbides characteristic in a rare-earth steel-bonded cemented carbide prepared by electroslag melting and casting

Tracking the evolution of microstructure and phases of WCoB-Co cermets during sintering

One-step synthesis of ultrafine WC–10Co hardmetals with VC/V 2 O 5 addition by plasma assisted milling

Decarbonization and Its Improvement of Coarse-Grained Low Cobalt Cemented Carbide Sintered by Microwave Irradiation

Comparative study of the microstructure and phase evolution of FeCoCrNiAl high-entropy alloy-matrix WC nanocomposite powders prepared by mechanical alloying

Comparative Study on Microstructure and Mechanical Properties of Coarse-grained WC-based Cemented Carbides Sintered with Ultrafine WC or (W+C) as Additives