Abstract:In this paper, dense MAX phase Ti3AlC2 enhanced and toughened TiAl3 matrix composites with mass fractions of 10∼40% were prepared by in-situ reaction via powder metallurgy route which using TiH2, Al and TiC powder as the starting materials. Then, the microstructure and phase structure of the composites were characterized, and the relationship between microstructure, mechanical properties and fracture mechanism was systematically investigated. The results show that the lath-like (micron level) and fine-needle-like (submicron level) reinforcements Ti3AlC2 are uniformly distributed in TiAl3 matrix. With the increases of mass fraction of reinforcements, the average grain size of the TiAl3 matrix decreases remarkably from 7.6 μm to 4.8 μm, indicating that the reinforcements Ti3AlC2 can effectively refine the matrix grains and plays a good pinning effect on the TiAl3 matrix. The prepared Ti3AlC2/TiAl3 composite with 30% mass fraction exhibits excellent comprehensive mechanical properties: the Vickers hardness, flexural strength, fracture toughness is 575 ± 5 HV, 470 ± 18 MPa, and 3.83 ± 0.05 MPa m1/2, 14.1%, 174.9% and 117.6% higher than that of the pure TiAl3 matrix, respectively. Both the strengthening and toughening effects are significant. The strengthening mechanism are fine grain strengthening and deformation strengthening, while the toughening mechanism is a synthetic effect in terms of crack deflection, crack bifurcation, grain refinement and stress-induced microcrack. Fracture analysis shows that the fracture mechanism is transgranular (cleavage) fracture.

Strength improvement and fracture mechanism in Fe40Al/TiC composites with high content of TiC

Mechanical Properties and Microstructure of Fe40al/Tic Composites with Low Content of Intermetallic

Effect of TiB_2 content on microstructure and mechanical properties of in-situ fabricated TiB_2/B_4C composites

Interpenetrating microstructure and fracture mechanism of NiAl/TiC composites by pressureless melt infiltration

Microstructure and Mechanical Properties of Ti2AlC-reinforced TiAl Composites

Preparation and toughness mechanism of in-situ Ti3AlC2 enhanced and toughened TiAl3 matrix composites

Simultaneous Improvement in Strength and Ductility of TC4 Matrix Composites Reinforced with Ti1400 Alloy and In Situ-Synthesized TiC

Preparation, Microstructure and Mechanical Properties of In-Situ TiC/Al–Si–Fe Aluminum Matrix Composites

In-situ TiC/Ti composites based on Ti 2 AlC–Ti system: Reaction process, microstructure, and mechanical properties

Microstructure and mechanical properties of Al2O 3/TiAl in situ composites doped with Fe2O3

The Flexural Strength and Fracture Toughness of TC4-Based Laminated Composites Reinforced with Ti Aluminide and Carbide

Densification, Microstructure and Mechanical Performance of TiC/Fe Composites by Spark Plasma Sintering

Reaction mechanism and microstructure evolution of superhigh strength in-situ TiC/Ti composite based on Cr 2 AlC-Ti system

Microstructure and High-Temperature Mechanical Properties of CrMnFeCoNi/TiAl Composites Prepared by Powder Metallurgy

Tailoring Ultrafine Grained and Dispersion-Strengthened Ti2AlC/TiAl Composite Via a New Fabrication Route

Processing, Microstructural Characterization and Mechanical Properties of in Situ Ti3AlC2/TiAl3 Composite by Hot Pressing

R-curve Behavior of TiC Particle Reinforced Al2O3 Composites

Influence of TiC particle size on microstructural evolution and fracture mechanism of TiC/Al-Cu composites

Thermomechanical Processing of a Near-α Ti Matrix Composite Reinforced by TiBw

Anisotropic microstructures and mechanical properties of textured Ti3AlC2/TiAl3/Al composite

Interfacial structures and strengthening mechanisms of in situ synthesized TiC reinforced Ti6Al4V composites by selective laser melting