Abstract:<p>On the eve of component procurement, this paper discusses the present physics basis for the first ITER tungsten (W) divertor, beginning with a reminder of the key elements defining the overall design, and outlining relevant aspects of the Research Plan accompanying the new "staged approach" to ITER nuclear operations which fixes the overall divertor lifetime constraint. The principal focus is on the main design driver, steady state power fluxes in the DT phases, obtained from simulations using the 2-D SOLPS-4.3 and SOLPS-ITER plasma boundary codes, assuming the use of the low Z seeding impurities nitrogen (N) and neon (Ne). A new perspective on the simulation database is adopted, concentrating purely on the divertor physics aspects rather than on the core-edge integration, which has been studied extensively in the course of the divertor design evolution and is published elsewhere. Emphasis is placed on factors which may increase the peak steady state loads: divertor target shaping for component misalignment protection, the influence of fluid drifts, and the consequences of narrow scrape-off layer heat flux channels. All tend to push the divertor into an operating space at higher sub-divertor neutral pressure in order to remain at power flux densities acceptable for the target material. However, a revised criterion for the maximum tolerable loads based on avoidance of W recrystallization, set an upper limit potentially ∼50% higher than the previously accepted value of ∼10 MWm<sup>−2</sup>, a consequence both of the choice of material and the finalized component design. Although the simulation database is currently restricted to the 2-D toroidally symmetric situation, considerable progress is now also being made using the EMC3-Eirene 3-D code suite for the assessment of power loading in the presence of magnetic perturbations for ELM control. Some new results for low input power corresponding to the early H-mode operation phases are reported, showing that even if realistic plasma screening is taken into account, significant asymmetric divertor heat fluxes may arise far from the unperturbed strike point. The issue of tolerable limits for transient heat pulses is an open and key question. A new scaling for ELM power deposition has shown that whilst there may be more latitude for operation at higher current without ELM control, the ultimate limit is likely to be set more by material fatigue under large numbers of sub-threshold melting events.</p>

Post examination of tungsten monoblocks subjected to high heat flux tests of ITER full-tungsten divertor qualification program

Progress of High Heat Flux Component Manufacture and Heat Load Experiments in China

Tungsten Joining with Copper Alloy and Its High Heat Load Performance

Thermal fatigue failure behavior on Be/Cu joint of ITER first wall after enhanced heat flux test

China’s Technological Achievements on ITER Enhanced Heat Flux First Wall in the Pre-Pa Qualification

Failure analysis of Be/Cu joint in ITER first wall mock-ups

Vacuum Hot-Pressed Beryllium and Tic Dispersion Strengthened Tungsten Alloy Developments for Iter and Future Fusion Reactors

Comparative study of ITER conform tungsten grades exposed to high heat flux and neutron irradiation damage

Microstructural analysis of the thermal fatigue tested Be/CuCrZr joint with artificial defects between Ti/Cu interlayers

Manufacturing and testing of ITER FW CuCrZr/316L(N)-IG explosive Bi-metallic plates

Interface cracking damage of W/Cu monoblocks as divertor target after high-cyclic plasma discharges in EAST

Mock-ups fabrication by HRP technology with advanced W-alloy monoblocks for DEMO divertor target

Manufacturing and Testing of W/Cu Mono-Block Small Scale Mock-Up for EAST by HIP and HRP Technologies

Thermal strain test and analysis of the W-ZrC mono-block mock-up

Failure analysis of damaged tungsten monoblock components of upper divertor outer target in EAST fusion device

Upgrade of Langmuir probe diagnostic in ITER-like tungsten mono-block divertor on experimental advanced superconducting tokamak.

Physics basis for the first ITER tungsten divertor

Lifetime measurement of a particular deep crack failure on a flat-type divertor mockup under cyclic high heat flux loading conditions

Surface Modifications of W Divertor Components for East During Exposure to High Heat Loads with He

Power Balance Investigation in Long-Pulse High-Performance Discharges with ITER-like Tungsten Divertor on EAST

Recent Studies of Tungsten-Based Plasma-Facing Materials in the Linear Plasma Device STEP