Abstract:The first wall of fusion reactor is a plasma-facing component and is a key link to maintain the integrity of the structure during thermal shock induced by plasma disruptions. Previous researches on thermal shock resistance of the first wall lacks coupled thermal/mechanical analysis on heat shock process based on practical operating conditions, such as material melting, solidification and even evaporation etc., which is significant to further understand the heat shock damage mechanism of first wall structures. With the aim to lean more detailed mechanical mechanism of thermal shock damage and then to improve the thermal shock resistance performance of first wall design, the coupled thermal/mechanical response of two typical structure of ITER-like first walls (with different plasma-facing material: one is traditionally Be, the other is functionally graded W–Cu) under the heat shock of 1–2 GW/m2 are computed by the finite element method. Special considerations of elastic–plastic deformation, material melting, solidification are included in numerical models and methods. The mechanical response behaviors of different structures and materials under normal servicing operation as well as plasma disruption conditions are analyzed and investigated comparatively. It is concluded that: (1) During the normal servicing operation state, both kinds of first walls manifest a good thermal and mechanical performance. However, the first wall with graded W–Cu material presents a more complex distribution and larger values of interfacial thermal stress and deformation. (2) In high energy shock pulse induced by plasma disruptions, heat is mainly deposited on PFM layer, complex thermal stress change as well as coupled melting and solidification processes in PFM layer are observed, involving a mechanical irreversible damage of repeated thermal elastic and plastic expansion, contraction and yielding. (3) The mechanically irreversible damages for both mock-ups under the thermal shock with H0 = 1–2 GW/m2 are mainly limited in PFM layer, the internal parts of both mock-ups are protected effectively. (4) In view of thermal/mechanical performance, the first wall with Be PFM mitigates the damages from heat shock at most only in PFM layer with cost of whole PFM layer plastic yielding, while the first wall with graded W–Cu PFM is potential of higher heat shock resistance performance, providing its material gradient as well as cooling capacity are well optimized under practical loading conditions.

Thermal fatigue failure behavior on Be/Cu joint of ITER first wall after enhanced heat flux test

Failure analysis of Be/Cu joint in ITER first wall mock-ups

Microstructural analysis of the thermal fatigue tested Be/CuCrZr joint with artificial defects between Ti/Cu interlayers

Study on the Microstructure and Properties Evolution of CuCrZr/316LN-IG Explosion Bonding for ITER First Wall Components

Effect of the Iter Fw Manufacturing Process on the Microstructure and Properties of A Cucrzr Alloy

Manufacturing and testing of ITER FW CuCrZr/316L(N)-IG explosive Bi-metallic plates

Progress of High Heat Flux Component Manufacture and Heat Load Experiments in China

China’s Technological Achievements on ITER Enhanced Heat Flux First Wall in the Pre-Pa Qualification

Effect of the First Wall Manufacturing on the Properties of CuCrZr Alloys

Tungsten Joining with Copper Alloy and Its High Heat Load Performance

Effect of explosive welding on properties of lTER-grade CuCrZr alloy

Neutron Irradiation Response Of Explosion-Welded Cucrzr/316ln Joints For Iter Application

Vacuum Hot-Pressed Beryllium and Tic Dispersion Strengthened Tungsten Alloy Developments for Iter and Future Fusion Reactors

Numerical Evaluation on Heat Shock Resistance of Two ITER-Like First Wall Mockups

Coupled Thermal-Mechanical Analysis of Two ITER-like First Wall Mockups under Heat Shock of Plasma Disruptions

Numerical simulation of the combined effects of plasma heating and neutron heating loads on the ITER first wall

Progress in Developing ITER and DEMO First Wall Technologies at SWIP

Progress Towards a Better Be/Cu Joining for ITER First Wall in China

Development and manufacturing of Beryllium-armoring ITER enhanced heat flux FW towards series production in China

Exploring of Two Connection Forms of the Tungsten Tile and CuCrZr Heat Sink for First Wall Mockup

High heat flux test and post examination of ITER divertor W/Cu monoblock mock-ups