Abstract:In this study, a micro/nano NbC reinforcement layer was prepared on a bearing steel surface by in-situ reaction method using GCr15 bearing steel and high purity niobium plate as raw materials. The rapid diffusion of C, strong carbide formation of Nb, and both melting and mass transfer of the matrix at certain temperatures easily controlled the gradient structure in the reinforcement layer. X-rays diffraction and X-ray photoelectron spectroscopy data revealed the presence of NbC, Fe3C, α-Fe, and Cr7C3 as the main phases in the reinforcement layer. The reinforcement layer can be divided into dense and gradient layers. SEM determined the volume fraction of NbC ceramic particles in the dense layer above 90%, with structure morphology close to that of a completely dense ceramic structure. The gradient layer was composed of two long-strip structures arranged alternately, with structure I consisting of dispersed NbC ceramic particles and structure II containing NbC ceramic particles embedded in the steel matrix. At the microscopic phase interface, the enhanced phase NbC particles were in direct contact with Fe3C without producing other transition phases, and NbC/Fe3C interface presented a non-coherent interface. The macroscopic interface characterized by Electron backscatter diffraction (EBSD) analysis showed consistent crystal orientation characteristics of NbC grains in the reinforcement layer. Also, the reinforcement layer was closely combined with the steel matrix without impurity holes. The macroscopic interfacial bonding strength displayed load scoring values from 0N to 100N without serious deformation failure behavior of the reinforcement layer.

Preparation of a gradient nanostructured surface TaC layer-reinforced Fe substrate by in situ reaction

Study on the Interface Microstructure of TaC/GCr15 Steel Surface Reinforced Layer Formed by In-Situ Reaction

Strain-induced Refinement and Thermal Stability of a Nanocrystalline Steel Produced by Surface Mechanical Attritiontreatment

Bonding properties and corrosion resistance of TaC-Fe enhanced layer on GCr15 surface prepared by in-situ hot pressing

TiC–Fe gradient coating with high hardness and interfacial adhesion strength on cast iron prepared by in-situ solid-phase diffusion method

TiC-Fe gradient coating on pure titanium fabricated by in-situ solid-phase diffusion: Toward superior hardness and interfacial adhesion strength

Microscopic and macroscopic interfacial studies of NbC reinforcement layer on GCr15 bearing steel surface prepared by in-situ reaction method

Microstructures and mechanical properties of functionally graded TiCN–TaC ceramics prepared by a novel layer processing strategy

Thermal/kinetic study of the formation mechanism of NbC-Fe composite layer on the surface of GCr15 prepared by hot pressure diffusion

In situ formation by laser cladding of a TiC composite coating with a gradient distribution

Study on Deposition of Biomedical Ta Coating on Ti6Al4V Alloy Substrate by CVD and Its Properties

Surface modification and twinning behavior in gradient graphene-based TiC/Ti6Al4V composite

Grain refinement of 1 at.% Ta-containing cast TiAl-based alloy by cyclic air-cooling heat treatment

Effect of TiC addition on the microstructure and properties of Ni3Ta–TaC reinforced Ni-based wear-resistant coating

Influence of TaC content on microstructure and mechanical performance of Ti(C,N)-based cermets fabricated by mechanical activation and subsequent in situ carbothermal reduction

Effect of Gradient Multilayer Design on Tribological Performance of TiN/TiSiN Coatings Prepared by Cathodic Arc Ion Plating

Microstructure and high-temperature wear properties of in situ TiC composite coatings by plasma transferred arc surface alloying on gray cast iron

Tuning structure, mechanical properties, and oxidation resistance of (Nb, Ta)C1- solid solution powders via the dissolution-precipitation process

Investigation on Microstructure and Wear Properties of an <i>In Situ</i> Synthesized TiC Gradient Coating

In-situ Ti(C, N) reinforced AlCoCrFeNiSi-based high entropy alloy coating with functional gradient double-layer structure fabricated by laser cladding

Microstructure and bond strength of niobium carbide coating on GCr15 prepared by in-situ hot press sintering