Abstract:TiAl intermetallic compounds, as a new kind of high-performance light-weight structural material, are widely applied in many fields. Titanium carbide (TiC) as the reinforcing phase could improve the mechanical properties, wear resistance, and heat-resistance stability of TiAl intermetallic compounds. Ti(Al, C) mixture powders were deposited by cold spraying at gas temperature of 250 °C, 450 °C, and 550 °C. Then, Ti(Al, C) coatings were annealed at temperatures of 650 °C for different times and following holding at 1100 °C for 3 h. The microstructure, microhardness, fracture toughness, and abrasive wear of Ti-Al composite coatings were investigated. The research results were that the particle size of mixture powders decreased as the ball milling time prolonging. Ti(Al) solid solution appeared in the mixture powders as the milling time increased to 30 h. The average porosity of the coating sprayed at 550 °C was the lowest (0.85%). The as-sprayed coatings exhibited the same phase compositions with the mixture powders. The coating sprayed at gas temperature of 550 °C has the highest microhardness and the lowest weight loss. Ti-Al intermetallic was in-situ synthesized after annealing at 650 °C. The average porosity of the annealed coating (sprayed at 450 °C) was the lowest. The content of Ti-Al intermetallic compounds of the annealed coating sprayed at 450 °C is the highest. The X-ray diffraction (XRD) analysis results are consistent with the EDS analysis of the annealed coatings after annealing at 650 °C. Ti-Al intermetallic compounds were almost completely formed in the three kinds of the coatings after annealing at 650 °C for 20 h and following holding at 1100 °C for 3 h. TiAl and TiAl3 intermetallic phases were in-situ synthesized in the coatings based on the energy dispersive spectroscopy (EDS) and XRD analysis. TiC was also in situ synthesized in the coatings as the annealing temperature increased to 1100 °C. The annealed coating (sprayed at 450 °C) has the highest microhardness, fracture toughness, and wear resistance properties after annealing at 1100 °C for 3 h.

Investigation on Microstructure and Wear Properties of an <i>In Situ</i> Synthesized TiC Gradient Coating

Microstructure and Mechanical Properties of TiC-Fe Surface Gradient Coating on a Pure Titanium Substrate Prepared in Situ

Abrasive wear characteristics of in-situ TiC-reinforced iron matrix surface gradient composites

Microstructural evolution, mechanical properties and wear behavior of in-situ TiC-reinforced Ti matrix composite coating by induction cladding

Process optimization, microstructure characterization, and tribological performance of Y 2 O 3 modified Ti6Al4V-WC gradient coating produced by laser cladding

Effect of Gradient Multilayer Design on Tribological Performance of TiN/TiSiN Coatings Prepared by Cathodic Arc Ion Plating

TiC–Fe gradient coating with high hardness and interfacial adhesion strength on cast iron prepared by in-situ solid-phase diffusion method

Effects Of Gradient Multilayer Structure On Tribological Property Of Tialsin Coating

Influence of Carbon Contents on the Structure and Tribocorrosion Properties of Tisicn Coatings on Ti6al4v

Fabrication, Microstructure and Abrasive Wear Characteristics of an in Situ Tantalum Carbide Ceramic Gradient Composite

TiC-Fe gradient coating on pure titanium fabricated by in-situ solid-phase diffusion: Toward superior hardness and interfacial adhesion strength

In situ formation by laser cladding of a TiC composite coating with a gradient distribution

In-situ Fabrication of Gradient Titanium Oxide Ceramic Coating on Laser Surface Textured Ti6Al4V Alloy with Improved Mechanical Property and Wear Performance

In Situ Formation of Tic Particulate Composite Coating with A Gradient Distribution by Laser Cladding

Evolution of microstructure and wear mechanism in laser clad Al0.5CoCrFeNiSi0.5Tix coatings in response to the Ti addition

Investigation of Wear-Resistant Property of TiC/Fe Ceramic Coating Produced by Self-Propagating High-Temperature Synthesis

Evolution of microstructure and wear mechanism in laser clad Al<sub>0.5</sub>CoCrFeNiSi<sub>0.5</sub>Tix coatings in response to the Ti addition

Microstructure and dry sliding wear evaluation of functionally graded coating deposited via atmospheric plasma spray

Microstructure evolution and mechanical properties of reactive plasma sprayed Ti3SiC2–Ti5Si3–TiC composite coatings

Microstructure, Microhardness, Fracture Toughness, and Abrasive Wear of In-Situ Synthesized TiC/Ti-Al Composite Coatings by Cold Spraying Combined with Heat Treatment

Microstructure and Fracture Toughness of Compact TiC-Fe Gradient Coating Fabricated on Cast Iron Substrate by Two-Step in Situ Reaction

Investigation on Microstructure and Wear Properties of an &lt;i&gt;In Situ&lt;/i&gt; Synthesized TiC Gradient Coating