Abstract:TiAl based alloys are attractive for use in advanced propulsion systems for aircraft and also in automobile engine parts due to their low density, high specific strength, high specific stiffness, good creep strength up to 700 degrees C and better high-temperature oxidation resistance than titanium alloys. However, the low room temperature ductility and poor formability limit the extensive application of TiAl based alloys. It has been found that the intermetallic matrix composites (IMCs) can provide the right combination of high-temperature strength and creep resistance, and overcome the problem of poor ductility and toughness at ambient temperatures. In this paper, Ti2AlC/Ti-44Al-6Nb-0. 3Y composite was prepared successfully by spark plasma sintering (SPS) from 1000 to 1200 degrees C,using element Ti, Al, Nb,Y and carbon nanotube(CNT) as parent materials. The phase constitution, microstructure and mechanical properties of Ti2AlC/Ti-44Al-6Nb-0. 3Y bulk materials were investigated. Results showed that Ti2AlC/Ti-44Al-6Nb-0. 3Y composite was composed of gamma-TiAl,Ti2AlC and a little amount of alpha(2)-Ti3Al phases, and the microstructure exhibited interpenetrating network structure character. When the sintering temperature was 1100 degrees C, the relative density of as-sintered bulk materials reached 98. 4%, and the compressive yield strength was higher than 1800MPa. With increasing the SPS temperature up to 1200 degrees C the TiAl grains became significantly coarsened, leading to clearly reduced mechanical properties.

Highly Textured Ti2AlN Ceramic Prepared Via Thermal Explosion Followed by Edge-Free Spark Plasma Sintering

Growth and texture of Spark Plasma Sintered Al2O3 ceramics: a combined analysis of X-rays and Electron Back Scatter Diffraction

Anisotropic microstructures and mechanical properties of textured Ti3AlC2/TiAl3/Al composite

Synthesis of High-Purity, Isotropic or Textured Cr2alc Bulk Ceramics by Spark Plasma Sintering of Pressure-Less Sintered Powders

Synthesis and Microstructure of Ti2AlN Ceramic by Thermal Explosion

Enhanced Grain Orientation Degree and Electrical Properties in PSN-PMN-PT Textured Ceramics under the Effect of Sintering Aids

Texture Evolution and Mechanical Behavior of Commercially Pure Ti Processed Via Pulsed Electric Current Treatment

Realization of an Ultrahigh Power Factor and Enhanced Thermoelectric Performance in TiS2 Via Microstructural Texture Engineering.

Fabrication of Textured Ti2AlC Lamellar Composites with Improved Mechanical Properties

Reactive consolidation of layered-ternary Ti2AlN ceramics by spark plasma sintering of a Ti/AlN powder mixture

Microstructure and Properties of TiN-reinforced W–Ti Alloys Prepared by Spark Plasma Sintering

Ultrafast high-temperature sintering of dense and textured alumina

Anisotropic Properties of Grain Orientated Bismuth Titanate Ceramics by Spark Plasma Sintering

Microstructures and Mechanical Properties of Ti-43Al-5V-4Nb-Y Alloy Consolidated by Spark Plasma Sintering

Distinct Anisotropy and a High Power Factor in Highly Textured TiS2 Ceramics Via Mechanical Exfoliation

Preparation of Textured Bismuth Titanate Ceramics Using Spark Plasma Sintering

Microstructural Evolution and Mechanical Properties of a High Yttrium Containing TiAl Based Alloy Densified by Spark Plasma Sintering

Preparation of Fe2AlB2 Material Via Thermal Explosion Induced by Spark Plasma Sintering

Fabrication of textured cordierite ceramics with low thermal expansion coefficient and custom structure via vat photopolymerization

Textured Pb(Mg1/3Nb2/3)O3-PbTiO 3 ceramics by templated grain growth

Fabrication of Ti2AlC/Ti-44Al-6Nb-0.3Y composite by spark plasma sintering