Abstract:This paper reports the possibility of developing advanced Ti6Al4V matrix composites (TMCs) with enhanced mechanical properties and highly improved resistance to wear and thermal degradation for structural and high-temperature aerospace applications. The synergetic effect of different weight compositions (1, 1.5 and 2 wt%) of ternary reinforcements consisting of h -BN, TiN and AlN nanoparticles on the characteristics of the microstructure, phase constitution, densification, mechanical, tribological and thermal stability of Ti6Al4V matrix composites developed by spark plasma sintering (SPS) is investigated. The unreinforced Ti6Al4V exhibited a two-phase microstructure made up of α/β phases, however the simultaneous reinforcements resulted in notable microstructural changes and emergence of nitride-rich secondary phases. The relative densities of the composites decrease with increasing reinforcement addition, whereas the nanohardness and elastic modulus values of the composites continue to improve with increasing reinforcement from 1 wt% (28.319 ± 0.525 GPa and 219.43 ± 6.77 GPa) to 2 wt% (55.642 ± 0.693 GPa and 314.59 ± 7.58 GPa) compared to the unreinforced Ti6Al4V (5.838 ± 0.323 GPa and 115.07 ± 3.63 GPa). The unreinforced alloy yields higher average COF values, while the composites at equivalent applied normal loads yield lower average COF values. Thus, in comparison to the unreinforced alloy, the produced composites exhibit considerably lower specific wear rates (with increasing applied normal load). Based on thermogravimetric analysis, the oxidized composite reinforced with 1 wt% of ternary reinforcements exhibits the highest thermal stability in the high-temperature oxidizing environment, as evidenced by its greatest resistance to oxidation and its smallest weight gain of 1.55%.

Reactive consolidation of layered-ternary Ti2AlN ceramics by spark plasma sintering of a Ti/AlN powder mixture

Reactive Synthesis of Polycrystalline Ti3AlC2 and Its Sintering Behavior

Microstructures and Mechanical Properties of Ti-43Al-5V-4Nb-Y Alloy Consolidated by Spark Plasma Sintering

Microstructure and Properties of TiN-reinforced W–Ti Alloys Prepared by Spark Plasma Sintering

A Synergetic Effect of Ternary Refractory Nitride Reinforcements on Densification, Mechanical, Tribological and Thermal Stability Characteristics of Spark Plasma Sintering-Developed Ti6Al4V Matrix Composites

Investigation on the in-situ reaction mechanism of Ti2AlC/TiAl composite prepared by spark plasma sintering

Mechanical Alloying and Spark Plasma Sintering of Ni-Al-Ti-B Powders for Fabricating Nanocrystailine (Tib+tib2)/ni-3(Al, Ti) Composite

Preparation of Ti2AlC through in-situ selective laser forming and reaction sintering

The Microstructure Evolution, Mechanical Properties and Densification Mechanism of Tial-Based Alloys Prepared by Spark Plasma Sintering

A beta-solidifying TiAl alloy reinforced with ultra-fine Y-rich precipitates

Synthesis of TiN/Ti3Al composite coatings on Ti6Al4V alloy by plasma spraying and laser nitriding

The spark plasma sintering of fine grained TiCN-Mo-Ni cermets

Microstructural Evolution and Mechanical Properties of a High Yttrium Containing TiAl Based Alloy Densified by Spark Plasma Sintering

In Situ Synthesis of Tin/Ti3al Intermetallic Matrix Composite Coatings on Ti6al4v Alloy

Preparation of fine-grains TiAl alloys by mechanical alloying and spark plasma sintering

Synthesis of Fine Grain Ti3sic2 by Spark Plasma Sintering with Additive of Aluminum

Spark Plasma Sintering Mechanisms of the Al-Zn-Mg-Cu Alloys and TiB2/Al-Zn-Mg-Cu Composites

Highly Textured Ti2AlN Ceramic Prepared Via Thermal Explosion Followed by Edge-Free Spark Plasma Sintering

In-situ Synthesis of TiN and its Effects on Fe-12Cr-6Al in Laser Powder Bed Fusion

Combustion synthesis of ternary carbide Ti3AlC2 in Ti–Al–C system

Mlicrostructure of TiAl/TiC cermet joint bonded by combustion synthesis