Abstract:Air-cooling from an intercritical (IC) temperature produced an acicular pearlite in ferrite structure and was effective in increasing the strength and ductility of ductile iron in sections up to 10 inches (250 mm). Five alloys were melted and poured as 3-inch Y-blocks, and IC heat treatment produced a fine-grained acicular pearlite + ferrite structure in all five alloys. The compositions ranged from 3.39–3.59% C, 2.34–2.45% Si, 0.29–0.44% Mn, 0.59–0.61% Cu and 0.24–1.78 % Ni, with CE ranging from 4.34 to 4.40. Samples were removed from the bottoms of the Y-blocks to obtain test samples for tensile and Charpy V-Notch (CVN) impact testing. The test samples were heat-treated at intercritical temperatures near the upper critical temperature (UCT) and cooled at various rates to simulate air-cooling of castings up to 10 inches (250 mm). Prior to intercritical heat treatment, experiments were conducted to determine the optimum heat treatment parameters. It was found that the path of the thermal cycle on heating to the IC temperature can affect the quality of the heat-treated structure. Among the things learned are the following: The lamellar austenite in ferrite structure persisted at temperatures as high as 60° F above the predicted UCT. Heat treatment at UCT + 20 °F produced the most dense, acicular pearlite + ferrite structure. Ferritizing prior to IC heat treatment minimizes the pearlite network in the cell boundaries. A minimum soak time of 2 h at the IC temperature is recommended. The lamellar structure is stable for at least 8 h. Copper appears to delay the time to reach equilibrium at the UCT. Nickel (at 1.8%) counteracts the Cu effect. The IC heat-treated samples displayed significantly higher ferrite contents over the as-cast materials. The high strength and elongation were attributed to grain refinement and increased ferrite contents, respectively. Furthermore, the material appears to be forgiving of marginal graphite structures. Despite the coarse graphite inclusions with poor shapes, 7–9% elongation was attained in test bars exceeding 60 ksi (414 MPa) yield strength when cooled as a 10-inch (250 mm) section.

The Influence Of Cast Structure On The Austempering Of Ductile Iron. Part 3. The Role Of Nodule Count On The Kinetics, Microstructure And Mechanical Properties Of Austempered Mn Alloyed Ductile Iron

Role of Austenitization Temperature on Structure Homogeneity and Transformation Kinetics in Austempered Ductile Iron

Characterization of Microstructral Morphology of Austempered Ductile Iron by Electron Microscopy

Simulating Anisotropic Thermal Conduction in Supernova Remnants I : Numerics and the Evolution of Remnants

Relationships Between Macrostructure and Microstructure in Lamellar Graphite Iron Castings

Effect of Aluminum, Copper and Manganese on the Structure and Properties of Cast Irons

Kinetic Transitions and Mn Partitioning During Austenite Growth from a Mixture of Partitioned Cementite and Ferrite: Role of Heating Rate

Revisiting the Effect of Casting Thickness and Austempering Temperature of Gray Iron

Influence of Austenite Stability on the Machinability of Different Grades of Austempered Ductile Iron (ADI) During Dry Turning Machining

Effect of Intercritical Austenitization and Starting Matrix on Martensite Start Temperature and Austenite Carbon Concentration in Ductile Iron

Influence of Cu on Properties of High Strength Ductile Cast Iron

Effect of the Austenitizing Temperature on Microstructure Evolution and Impact Toughness of a Novel Bainite Ductile Iron

Achieving Higher Strength and Ductility in Heavy-Section Ductile Iron Castings

Effect of Manganese on Microstructure and Properties of Cast Iron

Characterization of Microstructure and Mechanical Properties of High Chromium Cast Irons Using Sem and Nanoindentation

Effect of regular thicknesses on the microstructural and quantitative analysis for a hypo-eutectic ductile iron alloyed with Ni and V

Investigation on the Interrelationship between the Chemical Composition, Heat Treatment Parameters and the Phase Transformation Process, Microstructure Evolution and the Mechanical Properties of Austempered Steel

Numerical Simulation of Austempering Heat Treatment of a Ductile Cast Iron

Effects of Manganese and Heat Treatment on Mechanical Properties in Spheroidal Graphite Cast Iron

Analysis of phase transformation thermodynamics and kinetics and its relationship to structure-mechanical properties in a medium-Mn high strength steel

Influence of Intercritical Annealing on Microstructure, Ductility, and Toughness of Medium Mn Steels