Abstract:Air-cooling from an intercritical (IC) temperature produced an acicular pearlite in ferrite structure and was effective in increasing the strength and ductility of ductile iron in sections up to 10 inches (250 mm). Five alloys were melted and poured as 3-inch Y-blocks, and IC heat treatment produced a fine-grained acicular pearlite + ferrite structure in all five alloys. The compositions ranged from 3.39–3.59% C, 2.34–2.45% Si, 0.29–0.44% Mn, 0.59–0.61% Cu and 0.24–1.78 % Ni, with CE ranging from 4.34 to 4.40. Samples were removed from the bottoms of the Y-blocks to obtain test samples for tensile and Charpy V-Notch (CVN) impact testing. The test samples were heat-treated at intercritical temperatures near the upper critical temperature (UCT) and cooled at various rates to simulate air-cooling of castings up to 10 inches (250 mm). Prior to intercritical heat treatment, experiments were conducted to determine the optimum heat treatment parameters. It was found that the path of the thermal cycle on heating to the IC temperature can affect the quality of the heat-treated structure. Among the things learned are the following: The lamellar austenite in ferrite structure persisted at temperatures as high as 60° F above the predicted UCT. Heat treatment at UCT + 20 °F produced the most dense, acicular pearlite + ferrite structure. Ferritizing prior to IC heat treatment minimizes the pearlite network in the cell boundaries. A minimum soak time of 2 h at the IC temperature is recommended. The lamellar structure is stable for at least 8 h. Copper appears to delay the time to reach equilibrium at the UCT. Nickel (at 1.8%) counteracts the Cu effect. The IC heat-treated samples displayed significantly higher ferrite contents over the as-cast materials. The high strength and elongation were attributed to grain refinement and increased ferrite contents, respectively. Furthermore, the material appears to be forgiving of marginal graphite structures. Despite the coarse graphite inclusions with poor shapes, 7–9% elongation was attained in test bars exceeding 60 ksi (414 MPa) yield strength when cooled as a 10-inch (250 mm) section.

Influence of Cu on Properties of High Strength Ductile Cast Iron

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Effect of Copper on Microstructure and Properties of Cast Iron

Effect of Cu addition on hardness and microstructural features of low alloy white cast iron

Influence of Tungsten on Microstructure and Properties of As-Cast Hi-Cr Cast Iron

Effects of Cu Addition on the Microstructure and Properties of the Al–Mn–Fe–Si Alloy

Effect of Cu Content on Microstructure and Mechanical Properties for High-Strength Deposited Metals Strengthened by Nano-Precipitation

Effect of Aluminum, Copper and Manganese on the Structure and Properties of Cast Irons

Microstructure Evolution and Mechanical Property of Cu-Bearing High-Strength Steel Produced by Simulated Strip Casting

Investigation of microstructure evolution and mechanical properties of near-eutectic Fe2-CoNiCr C high entropy cast iron

Development of New Ductile Iron with Super-High Thermal Conductivity and Elongation

Effect of Cu on the strengthening and embrittling of an FeCoNiCr-xCu HEA

Microstructure Characterization of Cu-rich B2 Intermetallic Nanoprecipitates in an Austenite-Based High Specific Strength Steel

Achieving Higher Strength and Ductility in Heavy-Section Ductile Iron Castings

In-situ investigation of strengthening and strain hardening mechanisms of Cu-added medium-Mn steels by synchrotron-based high-energy X-ray diffraction

Effect of Manganese on Microstructure and Properties of Cast Iron

Tempering temperature dependence on the microstructure, mechanical properties and wear behaviour of a novel high chromium cast iron

Effects of Titanium, Cerium or Aluminum Addition on Microstructure and Mechanical Properties of Ductile Iron Castings

Effect of Cu on Solidification Microstructure and Solidification Process in High Carbon High Speed Steel Type Cast Alloy

Interface characteristics and mechanical properties of wire-arc depositing Inconel 625 superalloy on ductile cast iron

Effect of C addition on microstructure and mechanical properties of as-cast HEAs (Fe50Mn30Co10Cr10)100-xCx