Abstract:Air-cooling from an intercritical (IC) temperature produced an acicular pearlite in ferrite structure and was effective in increasing the strength and ductility of ductile iron in sections up to 10 inches (250 mm). Five alloys were melted and poured as 3-inch Y-blocks, and IC heat treatment produced a fine-grained acicular pearlite + ferrite structure in all five alloys. The compositions ranged from 3.39–3.59% C, 2.34–2.45% Si, 0.29–0.44% Mn, 0.59–0.61% Cu and 0.24–1.78 % Ni, with CE ranging from 4.34 to 4.40. Samples were removed from the bottoms of the Y-blocks to obtain test samples for tensile and Charpy V-Notch (CVN) impact testing. The test samples were heat-treated at intercritical temperatures near the upper critical temperature (UCT) and cooled at various rates to simulate air-cooling of castings up to 10 inches (250 mm). Prior to intercritical heat treatment, experiments were conducted to determine the optimum heat treatment parameters. It was found that the path of the thermal cycle on heating to the IC temperature can affect the quality of the heat-treated structure. Among the things learned are the following: The lamellar austenite in ferrite structure persisted at temperatures as high as 60° F above the predicted UCT. Heat treatment at UCT + 20 °F produced the most dense, acicular pearlite + ferrite structure. Ferritizing prior to IC heat treatment minimizes the pearlite network in the cell boundaries. A minimum soak time of 2 h at the IC temperature is recommended. The lamellar structure is stable for at least 8 h. Copper appears to delay the time to reach equilibrium at the UCT. Nickel (at 1.8%) counteracts the Cu effect. The IC heat-treated samples displayed significantly higher ferrite contents over the as-cast materials. The high strength and elongation were attributed to grain refinement and increased ferrite contents, respectively. Furthermore, the material appears to be forgiving of marginal graphite structures. Despite the coarse graphite inclusions with poor shapes, 7–9% elongation was attained in test bars exceeding 60 ksi (414 MPa) yield strength when cooled as a 10-inch (250 mm) section.

Achieving Higher Strength and Ductility in Heavy-Section Ductile Iron Castings

Microstructure evolution of heavy section ductile iron

Thermal Analysis of Solidification Process and Mechanical Properties in Heavy Section Ductile Iron Casting

Effect of Carbon and Cooling Rate on the Structure of Hypereutectic High Chromium Cast Iron in the Cast State and after Heat Treatment

Improving High-Temperature Performance of High Si-Alloyed Ductile Iron by Altering Additions

Effects of Manganese and Heat Treatment on Mechanical Properties in Spheroidal Graphite Cast Iron

Alternative Heat Treatments for Complex-Alloyed High-Cr Cast Iron Before Machining

The Effect of Heat Treatment on Microstructure of a High Chromium Cast Iron

Mechanical Properties and Fracture Toughness Prediction of Ductile Cast Iron under Thermomechanical Treatment

Influence of heat treatments on the microstructure and mechanical properties of Inconel 625 fabricated by directed energy deposition

High Ductile Medium Mn Lightweight Alloy: The Role of Intensive Quenching and Deep Cryogenic Treatment

Experimental Analysis of Mechanical Properties, Wear and Corrosion Characteristics of IS400/12 Grade Ductile Iron Casting

Annealing effects on the microstructure and properties of bulk high-entropy CoCrFeNiTi0.5 alloy casting ingot

Development of New Ductile Iron with Super-High Thermal Conductivity and Elongation

Influence of Cu on Properties of High Strength Ductile Cast Iron

Effects of Cooling Rate and TiC Nanoparticles on the Microstructure and Tensile Properties of an Al–Cu Cast Alloy

Experimental Analysis of Mechanical Properties, Wear and Corrosion Characteristics of IS500/7 Grade Ductile Iron Casting

Microstructure Evolution and Mechanical Properties of High Nb-TiAl Intermetallic Compounds during Heat Treatment

Effect of Intercritical Heat Treatment on Microstructure, Nano-Size Precipitation and Mechanical Properties of Fe–Ni–Cu–Al Low Carbon Steel

Mechanism Analysis for the Enhancement of Low-Temperature Impact Toughness of Nodular Cast Iron by Heat Treatment

Improving High-Temperature Mechanical Properties of Additively Manufactured Inconel 718 Through Heat Treatment