Abstract:It is well known that the mechanical properties of spheroidal graphite cast iron deeply depend on the volume of pearlite matrix microstructures. Therefore, the theoretical criterion of pearlite matrix nucleation is considered important in this graphite cast iron that to obtain the higher mechanical properties of graphite cast iron, the pearlite stabilizing element such as Mn or Cu is very important. The present work aims to study the influence of manganese (Mn) content and heat treatment on the mechanical properties of 3% or 4% (Solution Strengthened Ferritic Ductile Iron-SSFDI) of silicon (Si) containing spheroidal graphite cast irons. The six 3.6%C–3%Si melts with different chemical compositions from 0.2 to 1.7 mass% of Mn content were produced using a high-frequency induction furnace. The melt was poured into a Y-block CO 2 sand mold of 25 or 40 mm in thickness. The microstructure analysis and mechanical testing were performed for as-cast and some heat treatment conditions, such as annealing or air cooling. As a result, the tensile strength had a good relationship with the area fraction of pearlite, over 600 MPa in UTS, and high proof stress for some 3 or 4%Si–Mn series samples in the as-cast condition. By the heat treatment from the unique ( α + γ ) region, the 3% Si sample showed over 800 MPa and over 10% in elongation. And 4%Si–1.5%Mn (SSFDI) series sample showed over 600 MPa in UTS and over 15% in elongation which was prepared by annealing heat treatment to reduce to less than 5% of the area fraction of pearlite. This study suggests that it can be understood of the correlation between optimizing the heat treatment condition and mechanical properties of SSFDI cast irons.

Effect of Aluminum, Copper and Manganese on the Structure and Properties of Cast Irons

Effect of Manganese on Microstructure and Properties of Cast Iron

Effect of Copper on Microstructure and Properties of Cast Iron

Wear Behavior and Microstructure Changes of a High Chromium Cast Iron: The Combined Effect of Heat Treatment and Alloying Elements

Influence of Cu on Properties of High Strength Ductile Cast Iron

Effect of Mn Addition to Al–Si Alloy on the Layer Formed at the Interface with Cast Iron in Compound Casting

Effects of Cu Addition on the Microstructure and Properties of the Al–Mn–Fe–Si Alloy

Effect of Cu addition on hardness and microstructural features of low alloy white cast iron

Iron Intermetallic Phases in the Alloy Based on Al-Si-Mg by Applying Manganese

Effects of Titanium, Cerium or Aluminum Addition on Microstructure and Mechanical Properties of Ductile Iron Castings

Effects of Manganese and Heat Treatment on Mechanical Properties in Spheroidal Graphite Cast Iron

The Influence Of Cast Structure On The Austempering Of Ductile Iron. Part 3. The Role Of Nodule Count On The Kinetics, Microstructure And Mechanical Properties Of Austempered Mn Alloyed Ductile Iron

Effect of Silicon and Vanadium on the Composition of Carbide Phase in Mottled Medium-Alloy Chromium-Nickel Cast Iron

Influence of the iron additive on the microstructural behavior of an aluminum-copper foundry alloy B206

INFLUENCE OF BORON AND COOLING RATE DURING SOLIDIFICATION ON THE CHEMICAL COMPOSITION OF STRUCTURAL COMPONENTS OF COMPLEX-ALLOYED WHITE CAST IRONS OF THE Fe–C–Cr–Mn–Ni–Ti SYSTEM

Effects of Thermal Variables of Solidification on the Microstructure and Hardness of the Manganese Bronze Alloy Cu-24Zn-6Al-4Mn-3Fe

The Effect of the Substitution of Silicon by Aluminum on the Properties of Lamellar Graphite Iron

Effect of Copper and Nickel Content on the Corrosion Mechanisms in Ferritic Matrix Gray Cast Irons under Simulated Marine Environments

Microstructure and Mechanical Properties of High Boron White Cast Iron with about 4 Wt% Chromium

Effect of alloying elements W, Ti, Sn on microstructure and mechanical properties of gray iron 220

New Technologies of Aluminum Castings. Effect of Microstructure on Fracture Toughness of Cast and Forged Aluminum Casting Alloys.