Abstract:The objective of this work was to investigate and evaluate the effect of the cooling environment on the microstructure, secondary phase precipitates and mechanical properties of an as-cast cobalt alloy. The microstructure of castings has a large bearing on the mechanical properties, grain size, porosity and the morphology of carbide precipitates are thought to influence hardness, tensile strength and ductility. It is postulated that a greater understanding of microstructure and secondary phase precipitate response to casting parameters could lead to the optimisation of casting parameters and serve to reduce the requirement of thermo-mechanical treatments currently applied to refine as-cast structures and achieve adequate mechanical properties. Thermal analysis was performed to determine the critical stages of cooling. Ten millimetre diameter cylindrical specimens which could be machined into tension test specimens were cast and cooled under different conditions to impose different cooling rates. Analytical techniques such as optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive x-ray spectroscopy (EDX), tensile testing and micro-hardness testing were used to study the specimens. Parameters studied include grain size, secondary dendrite arm spacing, secondary phase precipitates, porosity, hardness, ultimate tensile strength, yield strength and elongation. The microstructure of as-cast Co-28Cr-6Mo was found to consist of a dendritic matrix with secondary phases precipitated at grain boundaries and interdendritic zones. These secondary phase precipitates consist of carbides, rich in chromium and molybdenum. The size and area fraction of carbides was found to decrease significantly with increasing cooling rate while the micro-porosity was only marginally affected. The as-cast grains are illustrated for the first time showing a significant difference in size between insulated and naturally cooled specimens. The secondary dendrite arm spacing was determined to be significantly affected by the various cooling environments and the mechanical properties of hardness, ultimate tensile strength and yield strength all increased with increasing cooling rate while the ductility decreased. Correlations between microstructural features and mechanical properties are proposed.

INFLUENCE OF BORON AND COOLING RATE DURING SOLIDIFICATION ON THE CHEMICAL COMPOSITION OF STRUCTURAL COMPONENTS OF COMPLEX-ALLOYED WHITE CAST IRONS OF THE Fe–C–Cr–Mn–Ni–Ti SYSTEM

Influence of Compositions and Heat Treatment on Metastability of Structure and Properties of Wear-Resistant Cast Irons of the Fe-Cr-Mn-C System

Effect of boron concentration on microstructures and properties of Fe–B–C alloy steel

Effect of Carbon and Cooling Rate on the Structure of Hypereutectic High Chromium Cast Iron in the Cast State and after Heat Treatment

Microstructure and Properties Variation of High-Performance Grey Cast Iron via Small Boron Additions

Effect of Chromium on Microstructure and Properties of High Boron White Cast Iron

Characterization of Microstructure and Phase Elemental Composition of 15 Wt.% Cr – 2 Wt.% Mo Cast Iron with Boron Addition

Microstructure and Crystallography of Borides and Mechanical Properties of Fe–B–C–Cr–Al Alloys

Effects of Cooling Rate on Borides Morphology and Structure in Cast Β-Solidifying Γ-Tial Alloy

Effect of Heat Treatment on Structure and Wear Resistance of High Chromium Cast Steel Containing Boron

Microstructure and Mechanical Properties of High Boron White Cast Iron with about 4 Wt% Chromium

The influence of cooling conditions on grain size, secondary phase precipitates and mechanical properties of biomedical alloy specimens produced by investment casting

Study on Microstructure and Properties of Cast High-Boron Middle-carbon Wear-resistant Alloy

Effect of Boron on the Microstructure and Properties of Semisolid Hypereutectic High Chromium Cast Iron

Structural-phase state and properties of heat and wear resistant cast irons of Cr–Mn–Ni–Ti system additionally alloyed with Al and Nb

Influence of Boron on Microstructure and Mechani cal Properties of Abrasive Wear Resistant Ductile Cast Iron

Effect of Aluminum, Copper and Manganese on the Structure and Properties of Cast Irons

IMPROVING THE PROPERTIES OF NICKEL-BASED SUPERALLOYS OF DIRECTED CRYSTALLIZATION BY OPTIMIZING THE CHEMICAL COMPOSITION

Effect of boron on microstructure evolution and properties of wear-resistant cast Fe–Si–Mn–Cr–B alloy

Microstructure and Mechanical Properties of High Boron Iron-Based Alloy Solidified in Different Moulds

State of Art on Boron White Cast Iron