Abstract:In this research, we creatively integrate the traditional methods of liquid precursor infiltration plus in situ precipitation with stereolithography-based 3D printing for the fabrication of Al2O3-ZrO2 ceramics to ensure the homogeneous distribution of ZrO2 particle in the alumina matrix. Our characterization results shows that this combination leads to the materials with significantly better performance. The Al2O3 specimen is soaked in a Zr4+ ion solution to induce infiltration, in-situ precipitation and then sintered. X-ray diffraction analysis of the thus-treated sample indicated that Al2O3 was the primary phase and t-ZrO2 was the secondary phase. Microstructural and EDS analysis showed that the ZrO2 particles were homogeneously distributed in the Al2O3 matrix, leading to inhibited grain growth. The samples soaked in solutions for different Zr4+ concentrations and sintered both at 1450 degrees C and 1550 degrees C showed improved mechanical properties as compared to those of pure alumina. Futhermore, the sample infiltrated using the solution with a concentration of 1.5 mol/L and sintered at 1450 degrees C showed similar fracture toughness (4.97 MPa m(1/2)) with the sample sintered at 1550 degrees C (5.06 MPa m(1/2)) but much better hardness (20.95 Gpa) than the sample sintered at 1550 degrees C (19.71 GPa). Therefore, this method could not only enhance the mechanical properties via introducing the second phase, but also lowers the sintering temperature by at least 100 degrees C, which would be beneficial for energy conservation and leads to significant advances in the 3D printing of ceramic components. (C) 2018 Elsevier B.V. All rights reserved.

Fabrication of Dense Zirconia-Toughened Alumina Ceramics Through a Stereolithography-Based Additive Manufacturing

Microstructure, mechanical properties, friction and wear performance, and cytotoxicity of additively manufactured zirconia-toughened alumina for dental applications

Towards high strengthening efficiency of equiaxed and platelet-shaped alumina reinforced zirconia ceramics with textured microstructure using DLP-based stereolithography

Fabrication of alumina ceramics with high flexural strength using stereolithography

Microstructure and mechanical properties of dense ZTA ceramics with high Cr2O3 solution

Fabrication of High-Performance Al2O3-ZrO2 Composite by a Novel Approach That Integrates Stereolithography-Based 3D Printing and Liquid Precursor Infiltration

Fabrication and Mechanical Properties of Homogeneous Zirconia Toughened Alumina Ceramics Via Cyclic Solution Infiltration and in Situ Precipitation

Fabrication of Complex-Shaped Zirconia Ceramic Parts Via a DLP-stereolithography-based 3D Printing Method

A novel method for fabricating brick-mortar structured alumina-zirconia ceramics with high toughness

R-curve of La2O3 doped Zirconia Toughened Alumina Composites Prepared via Stereolithography based 3D Printing

Preparation of excellent performance ZTA ceramics and complex shaped components using digital light processing 3D printing technology

Preparation and stereolithography 3D printing of ultralight and ultrastrong ZrOC porous ceramics

The Rising Crack Resistance Curve Behavior and Mechanism of La2O3 Doped Zirconia Toughened Alumina Composites Prepared Via Vat Photopolymerization Based 3D Printing

Preparation of Alumina-Toughened Zirconia Via 3D Printing and Liquid Precursor Infiltration: Manipulation of the Microstructure, the Mechanical Properties and the Low Temperature Aging Behavior

Additive manufacturing of dense zirconia ceramics by fused deposition modeling via screw extrusion

Preparation of ZTA composite ceramics derived from sol–gel method by DIW printing

UV-Curing Assisted Direct Ink Writing of Dense, Crack-Free, and High-Performance Zirconia-Based Composites With Aligned Alumina Platelets

Zirconia Toughened Alumina Ceramics via Forming Intragranular Structure

Facile method for preparing lamellar structured alumina-zirconia ceramics with high toughness

Stronger and Tougher Nanosized Dense Ceria-Doped Tetragonal Zirconia Polycrystals by Sinter-Hip

Fabrication and Mechanical Properties of ZrO2–Al2O3–SiC(w) Composites by Oscillatory Pressure Sintering