Abstract:This paper reports a high-speed packaging for Silicon Mach-Zehnder modulators (MZMs). The radio frequency (RF) input port of the package is commercially available GPPO type. High-frequency ceramic substrate is designed to shorten the length of gold wire to suppress the RF attenuation. Gratings and single-mode fibers using inclined-surface coupling are used to realize low-loss and large tolerance coupling. In measurement, clear eye diagrams with ER of 10.1 dB and 7.6 dB were obtained at 25 Gb/s and 40 Gb/s modulations. Silicon photonics has become a hot research topic in the field of optoelectronics in recent years, since silicon–based optical device can achieve high density integration, low power consumption, low cost photonic devices, realize monolithic integration with electronic devices, and it is compatible with traditional CMOS processes [1]. Silicon electro-optic modulators which are key devices in optoelectronic information transmission and processing have got great developments in recent years. High speed OOK silicon modulators have been demonstrated [2-4]. The silicon modulator packaging has also been studied [5-6]. However, the operating speed of packaged silicon modulators still need to be improved. Our butterfly package for silicon modulator is illustrated in Figure 1. Two main designs were applied for high speed packaging: the modulator chip was designed with reverse PN mode, whose PN junction capacitance is smaller and the modulator electrode was carefully designed using CPW travelling-wave electrodes; GCPW transmission lines with metallic holes were adopted to fabricate the high-frequency ceramic substrates to make the high-speed electrical signal effective loading on the electrode of the MZM chip. Since micro-strip-like line (MSL) mode in GCPW line might exist, which usually cause energy coupling of CPW mode and prompt a microwave resonant of transmission response in high frequency range [7], we made metallic holes on a transmission line to suppress the microwave resonant [8-9]. Grating coupler and single-mode fiber with inclined-surface are used in optical coupling. The advantages of this optical coupling method is larger misalignment tolerance and cheap cleaved fiber packaging. Nickel metal tube is installed close to the inclined-surface of single-mode fiber, the position and angle of the optical fiber is adjusted by special fixture clamping nickel metal tube and adjusting the special fixture. Assuming the optical fiber is parallel to the chip surface, there is a relation of θ=2*φ-90o. We choose the φ=51 deg. as our grating incidence angle is 12 degree. Eye-diagram measurements were carried to demonstrate the high-speed operation of the packaged modules. Experimental results were presented in Fig. 4(a) and 4(b). Clear eye diagrams with ERs of 10.1 dB and 7.6 dB were obtained at 25 Gb/s and 40 Gb/s modulation speed. By improving the welding between the pin of GPPO connector and ceramic substrates, further reducing the length of gold wires from the ceramic substrates to the modulator pads, the speed of the packaged MZM module could be higher.

3D Silicon Photonics Packaging Based on TSV Interposer for High Density On-Board Optics Module

Silicon Photonic Network-on-chip and Enabling Components

Design and Realization of Multi-Channel and High-Bandwidth 2.5D Transmitter Integrated With Silicon Photonic MZM

Optical Via for Silicon Photonic 3D-Integrations

Development of Silicon Photonic Devices for Optical Interconnects

3D Integrated Photonics Platform with Deterministic Geometry Control

High-speed packaging for silicon modulator

Chip-To-Chip Optical Interconnects Based on Flexible Integrated Photonics

High Density Vertical Optical Interconnects for Passive Assembly

Scalable 3D Silicon Optical Switch Based on CLOS Architecture

Multi-material heterogeneous integration on a 3-D Photonic-CMOS platform

Technology for high density optical integration on silicon

Silicon photonics for high-speed communications and photonic signal processing

Multi-dimensional Data Transmission Using Inverse-Designed Silicon Photonics and Microcombs

A versatile, inexpensive integrated photonics platform

Photonic Packaging: Transforming Silicon Photonic Integrated Circuits into Photonic Devices

A Monolithically-Integrated Chip-to-Chip Optical Link in Bulk CMOS

3D integration enables ultralow-noise isolator-free lasers in silicon photonics

Optoelectronic packaging for 16-channel optical backplane bus with VHOEs

Design of Feasible Si-Si3N4 Interlayer Polarization Beam Splitter Toward 3D Optical Interconnect

A 3D Integrated Energy-Efficient Transceiver Realized by Direct Bond Interconnect of Co-Designed 12 nm FinFET and Silicon Photonic Integrated Circuits