Abstract:A new way on the magnitude and position of direction change of shear deformation resulted from rolling geometry and friction described by two parameters of Rf and Rp changed with practical rolling conditions is established for analyzing rolling textures. It is found that {001} <110> shear texture is dependent on the parameters of Rf and Rp, and rolling neutral angle is at the middle point of rolling deformation zone, i.e. Rp = 0.5, which favors development of {001}<110> shear texture. The results show that the rolling textures simulated by taking into account of Rf and Rp changed with practical rolling conditions are in better agreement with the measured than that of Rp = 0.5 in rolled high purity Al. Introduction Rolling textures and deformation microstructures have been demonstrated to be changed with rolling geometry and friction on contact surfaces between rollers and sample in previous investigations [1, 2, 3], in which {001}<110> shear texture and micro-shear bands with Cube orientation were found in rolled high purity aluminum with heavier rolling friction. However, the presented ways on effect of rolling geometry and friction on rolling texture components were either simple or complex, and rolling neutral angle position was hypothesized to be at the middle point of rolling deformation zone (RDZ) in literatures [4, 5, 6]. In current investigation, shear deformation can conventionally be changed with practical rolling conditions including rolling geometry and friction, especially, the position of direction change of shear deformation, i.e., rolling neutral angle, is not hypothesized to be at the middle point of RDZ per pass. Development of rolling textures in high purity Al rolled up to different total engineering strains is studied by experiment and modeling. Application of practical conditions on rolling texture modeling Practical Rolling conditions. All that rolling conditions are constrained by three angles, α, β and γ, and a relationship of the three angles can be described as known as

Effect of Deformation Geometry and Friction on Shear Texture in High Purity Aluminum Foils

Effect of Direction Change of Shear Deformation on the Textures in Rolled High Purity Al

Micro-process of Cube Texture Formation in High Purity Aluminum Foils by Cross Shear Rolling

Influence Of Recrystallization Annealing On The Cube Texture In High-Purity Aluniinuni Foils

Effect of Residual Deformation Energy and Critical Heating Rate on Cubic Texture and Grain Growth Behavior of Severely Deformed Aluminum Foil

Deformation-texture evolution in deep drawing of cold-rolled 3104 aluminum alloy sheet

Crystal Plasticity Finite Element Simulation of Grain Evolution Behavior in Aluminum Alloy Rolling

Local Texture Evolution during Rolling Deformation of Single Crystals of {100} Orientation

The Early Stage Formation of Shear Orientations and the Stability of //ND Orientations During Hot Rolling in Electrical Steels

Crystal Plasticity Finite Element Simulation Study on Thread Rolling Pure Aluminum

Effect of different deformation and annealing procedures on non-magnetic textured Cu60Ni40 alloy substrates

Influence Of Trace Re And Annealing On The Recrystallization Textures Of High Purity Al Anode Foils

Microstructure and Texture Evolutions of Aa1050 Aluminum Alloy Cold Rolled to High Strains

Effect of texture types on microstructure evolution and mechanical properties of AZ31 magnesium alloy undergoing uniaxial tension deformation at room temperature

Texture development and mechanical behavior of Zircaloy-4 alloy plates fabricated by cold rolling and annealing

Effect of Microstructure on the Dimensional Stability of Extruded Pure Aluminum

Tailoring texture in a near-α titanium alloy: Insights from strain paths and cooling rate influences

Interpretation of the strain state during cross-roll rolling of aluminum by means of texture analysis

Microstructure and Texture Evolution in Cold-Rolled and Annealed Oxygen-Free Copper Sheets

Effect mechanism of texture orientation on mechanical properties and Hall-Petch relationship of CVCDE AZ31 magnesium alloy via crystal plastic finite element method (CPFEM)

Texture, Microstructure and Mechanical Properties of 6111 Aluminum Alloy Subject to Rolling Deformation