Abstract:Due to their high melting point, low density, and affordable price, TiC ceramics have emerged as one of the most promising ultrahigh temperature structural materials. However, its development and usage are severely constrained by its weak mechanical characteristics. The Ti2AlC-TiC and Ti3AlC2-TiC composites were synthesized by using the laminated metal-ceramic Ti2AlC/Ti3AlC2 as the binder, combined with high-temperature and high-pressure sintering technology (GPa order of magnitude confinement system). The thermal analysis shows that the exothermic heat of Ti/1.2Al/2TiC is less than that of 3Ti/1.2Al/2C, 2Ti/1.2Al/C, and 3Ti/1.5Al/C. The ratio of Ti/1.2Al/2TiC can suppress the thermal explosion phenomenon during the sintering process and improve the safety of the high-pressure sintering process. XRD results showed that the main composition of the sintered products was Ti2AlC-TiC at 2∼3.5 GPa and Ti3AlC2-TiC at 4∼5 GPa. As the sintering pressure increased from 2 GPa to 5 GPa, the bonding phase changed from Ti2AlC to Ti3AlC2. The thickness of the synthetic Ti3AlC2 layer is near 0.1 μm under 5 GPa. The average friction coefficient of Ti2AlC-TiC composites sintered 2 GPa with POM is as low as 0.1767, while the average friction coefficient of Ti3AlC2-TiC composites with POM increased to 0.3468∼0.3797. The wear width of Ti2AlC-TiC is lower than that of Ti3AlC2-TiC composites sintered under 4–4.5 GPa. The wear width of Ti3AlC2-TiC composites decreases following the rise of sintering pressure and is reduced to 0.3504 mm under 5 GPa. Ti2AlC-TiC and Ti3AlC2-TiC composites with PP ball counterparts have friction coefficients of 0.375 to 0.45 and worse wear resistance than that of POM balls. Ti3AlC2-TiC composites synthesized at 5 GPa with a Cu ball had the smallest friction coefficient (0.4558) and the smallest wear scar width (0.6289 mm). The friction coefficients and wear widths of synthetics with Al pairs ranged from 0.48–0.697 and 0.851–1.087 mm, respectively, and varied irregularly with increasing sintering pressure. Ti2AlC-TiC composites synthesized at 2 GPa with agate and glass pairs have coefficients of friction of 0.5 and 0.61, respectively. Abrasion widths of Ti2AlC-TiC composites synthesized at 2 GPa with agate and glass pairs were 1.3 mm and 0.72 mm, respectively. The friction coefficient of synthetics with agate and glass pairs increases with increasing sintering pressure. The magnetization and magnetization intensity of the Ti3AlC2-TiC composites are stronger than those of Ti3AlC2. Ti2AlC-TiC and Ti3AlC2-TiC composites held promise to serve in the field of ceramic grinding processing applications.

PRODUCING TiC_p/2024 COMPOSITES BY MEANS OF INCREASING PRESSURE UNDER VACUUM

Oxidation behavior of in situ TiCp/Ti6Al4V composite with self-assembled network microstructure fabricated by reaction hot pressing

Microstructure and Properties of TiCp/Fe Hierarchical Composites Prepared by a New Pressure Infiltration Method

Study on the enhancement mechanism of (TiC + B 4 C)/6061Al composite fabricated via vacuum hot-press sintering

Effect of Ti Doping on the Microstructure and Properties of SiCp/Al Composites by Pressureless Infiltration

In-situ TiC/Ti composites based on Ti 2 AlC–Ti system: Reaction process, microstructure, and mechanical properties

Microstructure evolution, mechanical properties, and wear behavior of in-situ TiCx/TC4 composites

Densification behavior, mechanical and electrical properties of in-situ TiB 2p /Cu composite powder via vacuum hot pressing

Reaction mechanism and microstructure evolution of superhigh strength in-situ TiC/Ti composite based on Cr 2 AlC-Ti system

Microstructure and high-temperature mechanical properties of co-continuous (Ti3AlC2+ Al3Ti)/2024Al composite fabricated by pressureless infiltration

Pressureless manufacturing of high purity Ti3AlC2 MAX phase material: Synthesis and characterisation

Microstructure of In-Situ Synthesized (tib+tic)/ti Composites Prepared by Hot-pressing

Preparation and Sinterability of Submicron Titanium Carbide Powders Synthesized with Phenolic Resin As Carbon Source by Carbothermal Reduction

Processing, Microstructural Characterization and Mechanical Properties of in Situ Ti3AlC2/TiAl3 Composite by Hot Pressing

The Influence of Sintering Pressure on the Preparation, Friction Properties, and Magnetic Properties of Ti2AlC-TiC and Ti3AlC2-TiC Composites Under High-Pressure and High-Temperature

Microstructure and properties of TiCx/TC4 composites with a quasi-network structure prepared by the decomposition of the Ti2AlC precursor

Microstructure, Microhardness, Fracture Toughness, and Abrasive Wear of In-Situ Synthesized TiC/Ti-Al Composite Coatings by Cold Spraying Combined with Heat Treatment

Preparation and organization of W-Ni/TiC composite material

In-situ Production and Microstructure of TiC/Fe3 Al Composites

Design and Strengthening Behaviour of Ti2alc/Tial Composite by Low-Temperature Hot-Pressing Process

Microstructure and Wear Resistance of TiCp/Ti6Al4V Composite Coatings by Follow-Up Ultrasonic-Assisted Laser Additive Manufacturing