Abstract:In the present work, (TiBw+TiCp)/Ti6242 composites with TiB:TiC=1:1 were produced by common casting and hot-forging technology utilizing the SHS reactions between titanium and B4C, C powder. The microstructures of composites were examined using optical microscopy (OM) and transmission electron microscopy (TEM). The X-ray diffraction (XRD) was used to identify the phases that were present in the composites. There are three phases — TiB, TiC and titanium matrix alloy. TiB grows in short-fiber shape, whereas TiC grows in dendritic, equiaxed or near-equiaxed shape. TiB whiskers were made to align the longitudinal direction and TiC dendritic was broken up after hot-forging. The reinforcements are distributed uniformly in matrix alloy. The interfaces between reinforcements and titanium matrix alloy are very clean. The tensile strength (yield strength and ultimate tensile strength) and the Young's modulus improve with the addition of TiB whiskers and TiC particles although some reduction in ductility is observed. (TiBw+TiCp)/Ti6242 composites with TiB:TiC=4:1 will fracture on a lower level of applied stain due to deformation restraint of TiB whiskers on titanium matrix alloy. The (TiBw+TiCp)/Ti6242 composites with TiB:TiC=1:1 show higher tensile strength and ductility. The addition of graphite not only improves the tensile strength and the Young's modulus but also increases the ductility. The improved Young's moduli and increased tensile strengths of the composites are explained using shear lag and rule-of mixtures theories. The Young's moduli of the composites were found in good agreement with that calculated from Tsai–Halpin equation applied for discontinuous-reinforced composites.

Microstructure of In-Situ Synthesized (tib+tic)/ti Composites Prepared by Hot-pressing

In Situ TiBw/Ti–6Al–4V Composites with Novel Reinforcement Architecture Fabricated by Reaction Hot Pressing

In situ (TiBw+TiCp)/Ti6Al4V composites with a network reinforcement distribution

Microstructure and tensile properties of in situ synthesized (TiBw + TiCp)/Ti6242 composites

Microstructure and Mechanical Properties of in Situ Synthesised (Tic+tib)/ti-6Al-4v Composites Prepared by Powder Metallurgy

Microstructure And Compressive Properties Of In Situ Synthesized (Tib Plus Tic)/Ti Composites

Microstructure and Tensile Properties of in Situ Synthesized (Tib+tic)/ti-6Al-4v Composites

Microstructure and compressive properties of in situ synthesized (TiB + TiC)/Ti composites

Microstructure and Tensile Properties of in Situ (tib+tic)/ti6242 (tib:Tic=1:1) Composites Prepared by Common Casting Technique

TEM Characterization of Symbiosis Structure of in Situ TiC and TiB Prepared by Reactive Processing of Ti–B4C

Compressive Properites and Microstructure of In-Situ TiB Whisker and TiC Particulate Mixture-Reinforced Ti Composite

Fabrication and High Temperature Creep Behavior of in Situ Synthesized (tib+tic)/ti Composites

Microstructure and mechanical properties of reaction synthesized TiB/Ti-4.0Fe-7.3Mo composites by hot press sintering

Microstructure evolution during preparation of in-situ TiB reinforced titanium matrix composites

Microstructure Formation Mechanism of (al2o3+tib2+al3ti)/al Composites Fabricated by Reactive Hot Pressing

Microstructure and tensile behavior of novel laminated Ti-TiBw/Ti composites by reaction hot pressing

Microstructure and Residual Stress of In-situ Synthesized (tic+tib)/ti Composites

Microstructural Characterisation Ofin Situtib/ti Matrix Composites Prepared by Mechanical Alloying and Hot Pressing

Microstructure and Compressive Properties Ofin SituSynthesized TiC/Ti Composites

Microstructure, mechanical properties and strengthening mechanisms of in-situ prepared (Ti5Si3 + TiC0.67)/TC4 composites

Microstructural characterization and mechanical properties of (TiC+TiB)/TA15 composites prepared by an in-situ synthesis method