Abstract:We present a detailed optimization of a hole selective rear contact for p–type crystalline silicon solar cells which relies on full-area processes and provides full-area passivation. The passivating hole-contact is based on a layer stack comprising a chemically grown thin silicon oxide, an intrinsic silicon interlayer, and an in-situ boron-doped non-stoichiometric silicon-rich silicon-carbide layer on top. After deposition, the structure is annealed at 775–900°C to diffuse dopant impurities to the c-Si wafer and a hydrogenation step is carried out. It is shown that hydrogenation is essential to obtain high quality surface passivation. In particular, we compare the effect of annealing in forming gas and annealing with a silicon-nitride overlayer as hydrogen source. We present a systematic optimization of the hole-selective contact, for which we varied the doping concentration, annealing parameters and report the implied open circuit voltage (iVoc) and combined specific contact resistivity (ρc). It is observed that for highly doped layers the optimum annealing temperature for high quality surface passivation is 800°C while for lowly doped layers the optimum annealing condition shifts to 850°C. Excellent surface passivation and efficient current transport is evidenced by an iVoc value of 718mV which corresponds to a saturation current density (J0) of 11.5fA/cm2 and a ρc of 17mΩcm2 on p−type wafers. Moreover, the evolution of the boron diffusion profiles with different annealing conditions is investigated. Finally, we demonstrate proof-of-concept p−type hybrid solar cells employing the full-area hole-selective rear contact presented here and standard heterojunction front electron contact. The excellent efficiency potential of our passivating rear contact is highlighted by conversion efficiencies up to of 21.9%, enabling Voc of 708mV, FF of 79.9% and Jsc of 38.7mA/cm2.

Improving Performance of Bifacial‐Grid III–V Solar Cells Bonded on Glass by Selective Contact Annealing

Improved Performance of Electroplated CZTS Thin-Film Solar Cells with Bifacial Configuration

Improved performance of GaAs-based micro-solar cell with novel polyimide/SiO 2 /TiAu/SiO 2 structure

Investigation of the effect of forming gas annealing on front silver electrodes of c-Si solar cells

Thermal Radiation Annealing for Overcoming Processing Temperature Limitation of Flexible Perovskite Solar Cells

Post-Fabrication Annealing Effects in Polymer-Nanotube Photovoltaic Cells

Fabrication of High Voltage GaAs Micro-Solar Cell Arrays

Dark and illuminated J(V) characteristics of thin layered bulk heterojunction P3HT:PCBM sandwich solar cells after thermal treatment

Improvement of Surface Morphology of Thin ?lms and Performance by "electrical Annealing" on Polymer Solar Cells

Solvent Annealing Enabling Reconstruction of Cadmium Sulfide Film for Improved Heterojunction Quality and Photovoltaic Performance of Antimony Selenosulfide Solar Cells

Two-stage annealing-induced secondary grain growth for enhanced efficiency in CdTe solar cells on flexible polyimide foils

Effect of Vacuum Rapid Annealing Treatment on Performance of CIGS Solar Cells

EFFECT OF GLASS FRIT WETTING PROPERTY ON THE PERFORMANCES OF SILICON SOLAR CELLS

Diamine Surface Passivation and Post-Annealing Enhance Performance of Silicon-Perovskite Tandem Solar Cells

Interplay of annealing temperature and doping in hole selective rear contacts based on silicon-rich silicon-carbide thin films

Simulation and experimental study of a novel bifacial structure of silicon heterojunction solar cell for high efficiency and low cost

Fluorocarbon‐based Solvent‐Bath Annealing for High‐Performance Perovskite Photovoltaics

The effect of the curing process on illuminated annealing of silicon heterojunction solar cells

Au Nanocluster Assisted Microstructural Reconstruction for Buried Interface Healing for Enhanced Perovskite Solar Cell Performance

Effective Non-Radiative Interfacial Recombination Suppression Scenario Using Air Annealing for Antimony Triselenide Thin-Film Solar Cells

Carrier Injection and Annealing‐Enhanced Electrical Performance in Tunnel Oxide‐Passivated Contact Silicon Solar Cells