Abstract:In this current investigation, the impact of Nickel (Ni) on the microstructural attributes and properties of a cold-rolled 316L sheet was examined. The microstructure and phase configuration of austenitic stainless steels, specifically 316L and 316LNi, were meticulously characterized through the utilization of metallography, X-ray Diffraction (XRD), and Electron Backscatter Diffraction (EBSD) techniques. Subsequent assessments were conducted to evaluate magnetic characteristics, microhardness, and tensile properties. The phase structure of both austenitic stainless steels conforms to a Face-Centered Cubic (FCC) crystal lattice, whereby the grain content oriented along the (110) plane progressively escalates with augmenting degrees of cold rolling. The magnetic conductivity of these austenitic stainless steels satisfactorily adheres to established standards. The incorporation of Nickel (Ni) into the alloy composition enhances the cold deformation capacity of 316L stainless steel. However, substantial plastic deformation yields heightened dislocation density, thereby promoting enlarged grain dimensions upon solution treatment. Throughout subsequent cold rolling deformation sequences, the augmented grain size observed in 316LNi stainless steel leads to a reduction in dislocation density within the equivalently ordered cold-rolled plate. Simultaneously, this augmented grain size engenders a decline in grain boundary content coupled with an augmentation in twin content. Consequently, the interplay of grain coarsening, diminished dislocation density, and twin-induced softening collectively bestows upon 316LNi stainless steel a lower tensile strength compared to 316L stainless steel, albeit accompanied by heightened plasticity.

Understanding the Effect of Ni on Mechanical and Wear Properties of Low-Carbon Steel from a View-Point of Electron Work Function

Electron Work Function–a Promising Guiding Parameter for Material Design

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Dependence of the Mechanical Behavior of Alloys on Their Electron Work Function—an Alternative Parameter for Materials Design

Correlation Between the Wear Resistance of Cu-Ni Alloy and Its Electron Work Function

Effects of Cr and Ni on the microstructure and corrosion resistance of high-strength low alloy steel

Effect of Nickel on Hardening Behavior and Mechanical Properties of Nanostructured Bainite-Austenite Steels

Investigation on Microstructure and Properties of Low‐Carbon Wear‐Resistant Steels with Addition of Cr and Ni

Synergistic Effect of Al and Ni on Microstructure Evolutions and Mechanical Properties of Fe-Mn-Al-C Low-Density Steels

Effect of Microalloying Addition on Microstructure and Mechanical Properties of Ni-W Coatings

Electron work function: an indicative parameter towards a novel material design methodology

Effects of Nickel on the Microstructure, Mechanical properties and Corrosion Resistance of CoCrFeNixAl0.15Ti0.1 High Entropy Alloy

Characterization of microstructure, grain distribution, and tribocorrosion properties of NiTi-based alloy

Effect of Tungsten on Microstructures of Annealed Electrodeposited Ni-W Alloy and Its Corrosion Resistance

Effect of Ni on Corrosion Fatigue Properties of Medium Carbon High Strength Spring Steel

Effect of Ni element on microstructure and properties of cold-rolled 316L austenitic stainless steel

Effect of Ni addition on the microstructure, conductivities and mechanical properties of as-cast Al-Fe alloys

Influence of Ni content on impact-abrasion wear resistance of medium-carbon low alloy cast steel

Effects of Ni content on microstructure and wear behavior of Al–13Si–3Cu–1Mg-xNi-0.6Fe-0.6Mn alloys

The Effect of N Content on the Microstructure and Wear Resistance of Improved High-Carbon Chromium Bearing Steel

Wear and Corrosion Properties of Crystalline Ni-W Alloy Coatings Prepared by Electrodeposition