Abstract:Transition metal boride enable applications in fields of cutting tools as the hard phase, but their fabrication suffers from shortcomings in high temperature for binary and hard/soft phase balance. Here, we leveraged a WCoB-Co cermets prepared by using elemental powders of W, Co and B powders via in situ synthesis method and investigated the microstructure evolution of a composite structure of WCoB/Co. The phase evolution, microstructure evolution and mechanical properties were investigated using X-ray diffraction (XRD), differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and energy dispersive spectrometer (EDS). The complete sintering process consist of three solid-phase reaction stages and one liquid-phase sintering stage. The solid-phase reaction stage includes the following three reactions: B + 2Co → Co2B, 11 W +15 Co2B → 9WCoB + W2Co21B6, and 14 W + 2W2Co21B6 → 12WCoB + 23Co + Co7W6. The eutectic liquid phase, essential for the densification, forms at 1323 °C. The Rockwell hardness and density value reach 87.5HRA and 12.11 g/cm3, respectively. At 1380 °C, the traverse rupture strength (TRS) reaches the peak value of 1495 MPa. Moreover, the results show that transgranular fracture is the main fracture mode. The densification stage was completed at ~1400 °C. In particular, Co7W6 phase was discovered during the study of the evolution of WCoB-Co cermets. An increase of the B content was found to be beneficial to eliminate the Co7W6 phase that proved to be detrimental to mechanical properties.

Properties of WC–8Co Hardmetals with Plate-Like WC Grains Prepared by Plasma-Assisted Milling

Achieving high transverse rupture strength of WC-8Co hardmetals through forming plate-like WC grains by plasma assisted milling

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Achieving Combination of High Hardness and Toughness for WC-8Co Hardmetals by Creating Dual Scale Structured Plate-Like WC

One-step synthesis of ultrafine WC–10Co hardmetals with VC/V 2 O 5 addition by plasma assisted milling

Coarse-grained WC–6Co hardmetals with dual-scale and plate-like WC structures fabricated by convention powder metallurgy process

Fabrication and Properties of Axisymmetric WC/Co Functionally Graded Hard Metal via Microwave Sintering

Effect of particle size and high-energy ball milling time on microstructure and mechanical properties of WC-10Co cemented carbides with plate-like WC grains

Microstructure and mechanical properties of WC-(Ti,W)C-Co hardmetals fabricated by in-situ carbothermal reduction of oxides and subsequent liquid phase sintering

Breaking the hardness–toughness trade-off in WC–Co hardmetals: Introduction of dual-scale plate-like WC and modification of prediction models

Effect of WO3 content on microstructure and mechanical properties of dual-grain structured hardmetals fabricated by in-situ carbothermal reduction of WO3

Microstructure and Mechanical Properties of WC-10wt.%AlCoCrFeNi Cemented Carbides Fabricated by Plasma-Assisted Ball Milling

WC-Co Composite Coating Deposited by Cold Spraying of a Core-Shell-Structured WC-Co Powder

Preparation of WC-Co Cemented Carbide by Spark Plasma Sintering: Microstructure Evolution, Mechanical Properties and Densification Mechanism

Mechanical Properties and Microstructural Behaviour of Microwave Sintered WC–Co

Influence of Powder Structure on the Micro-Hardness and Fracture Toughness of Cold-Sprayed WC-12Co Deposit

Microstructure and wear performance of a WC-8Co hard alloy modified using W powders doped with Y 2 O 3

L1 2 strengthening of WC-CoNiFe cemented carbides by spark plasma sintering

Tracking the evolution of microstructure and phases of WCoB-Co cermets during sintering

Investigation on morphology evolution of coarse grained WC–6Co cemented carbides fabricated by ball milling route and hydrogen reduction route

Study on Elemental Composition and Interfacial Structure of the Second Phase in WC-8Co Hard Alloy Doped with Rare Earth Components