Abstract:An equiatomic NiFeCrWMo high-entropy alloy (HEA) produced by mechanical alloying was used as a binder alternative to cobalt for the manufacture of WC-based hardmetals. The WC–10 HEA (wt.%) powder mixture was homogenized in a planetary-ball mill for 2 h and consolidated by electron beam sintering (EBS) for 4 min at a temperature of 1450°C and spark plasma sintering (SPS) for 10 min at a temperature of 1400°C. The relative density of the sintered samples reached 99.4%. The phase composition, microstructure, and mechanical properties of WC–10 HEA hardmetals were studied by X-ray diffraction, scanning electron microscopy, and microindentation. The effect of the NiFeCrWMo HEA binder on the microstructure and mechanical properties of WC–10 HEA hardmetals in comparison with the conventional VK8 hardmetal (WC–8 Co) was determined. The WC–10 HEA hardmetal consolidated by EBS consisted of WC grains, a NiFeCrWMo HEA binder with a bcc structure, and a small amount (3.5%) of complex carbide (Ni, Fe, Cr) x W y C z , whereas the amount of the complex carbide after SPS increased to 47% due to longer sintering and pressure application. No noticeable growth of WC grains was observed during sintering of the WC–10 HEA hardmetal because of the multielement composition of the NiFeCrWMo HEA binder and the formation of complex carbide (Ni, Fe, Cr) x W y C z layers, preventing the growth of WC grains. The hardness HV and fracture toughness K Ic of WC–10 HEA hardmetals after EBS were 18.9 GPa and 11.4 MPa · m 1/2 and those after SPS were 19.9 GPa and 10.8 MPa · m 1/2 . The hardmetals with a HEA binder exhibit an excellent combination of hardness and fracture toughness. These values are higher than those for the conventional VK8 hardmetal (WC–8 Co) produced by EBS for 4 min at 1350°C, whose hardness is 16.5 GPa and fracture toughness K Ic is 9.5 MPa · m 1/2 .

Microstructure and Mechanical Properties of WC-10wt.%AlCoCrFeNi Cemented Carbides Fabricated by Plasma-Assisted Ball Milling

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

Microstructure and properties of WC-Co/CrMnFeCoNi composite cemented carbides

Comparative study of the microstructure and phase evolution of FeCoCrNiAl high-entropy alloy-matrix WC nanocomposite powders prepared by mechanical alloying

Microstructure and properties of coarse WC-10CoCrFeMnNi cemented carbide by mechanical alloying and hot pressing sintering

Insight into Grain Refinement Mechanisms of WC Cemented Carbide with Al0.5CoCrFeNiTi0.5 Binder

Metastable FeCrMnCo HEAs with the reinforcement of tungsten carbide fabricated by laser melting: Microstructure, mechanical properties and tribological behaviors

The Effect of Carbon Content on the Microstructure and Mechanical Properties of Cemented Carbides with a CoNiFeCr High Entropy Alloy Binder

Effect of Al content in CoCrFeNiAl x HEA on mechanical properties and high temperature oxidation resistance of WC-10%CoCrFeNiAl x hard alloy

Study on Effect of High-Entropy Alloy Binder on Microstructure and Properties of WC Cemented Carbide Doped with Rare Earth Oxide

Effects of milling time and sintering temperature on the mechanical properties of 8 wt% WC/AlCoCrFeNiTi 0.5 high entropy alloy matrix composite

Effect of Cr3C2 Addition on Microstructure and Mechanical Properties of WC-CoNiFe Cemented Carbides

WC-based cemented carbide with NiFeCrWMo high-entropy alloy binder as an alternative to cobalt

Structure and Mechanical Properties of WC-Based Hardmetal with a High-Entropy NiFeCrWMo Binder

Study on Microstructure and Properties of WC Particle-Reinforced FeCoCrNi-Matrix High Entropy Alloy Composites

Microstructure evolution and wear resistance of a novel ceramic particle-reinforced high-entropy alloy prepared by laser powder bed fusion

Effect of High‐Energy Ball‐Milling Duration on Densification, Microstructure, and Mechanical Properties of Cr2AlC‐Dispersed 90W‐6Ni‐2Fe‐2Co Heavy Alloys

Microstructure and Properties of NiCoCrAlTi High Entropy Alloy Prepared Using MA-SPS Technique

Microstructural evolution and mechanical characterization of a WC-reinforced CoCrFeNi HEA matrix composite

WC-Based Cemented Carbides with High Entropy Alloyed Binders: A Review

Microstructure and mechanical properties of CoCrFeNiTa high entropy alloy prepared by mechanical alloying and spark plasma sintering