Abstract:WC-Co cemented carbides are widely used in the fields of military, aerospace, mining and cutting industry etc. In this paper, a new two-step method for the preparation of WC-Co cemented carbides was proposed. First, the mixture of yellow tungsten trioxide (WO3) and cobaltic oxide (Co2O3) were reduced by carbon black to remove all the oxygen. Then, the carbothermic reduction products were precisely mixed with an appropriate amount of carbon black to directly prepare WC-Co cemented carbides. The effects of C/WO3 ratio on the phase composition, morphological evolution, particle size and mechanical properties of products are investigated. The experimental results revealed that when the C/WO3 molar ratio was above 2.7, all oxygen in the raw material mixture were removed by carbon black and a mixture of W2C and η-phase were obtained after the first step of carbothermic reduction at 1150 °C for 2 h; then, the mixture of carbothermic reduction product and an appropriate content of carbon black was compacted, and the green compact was first carbonized at 1200 °C for 2 h and then sintered at 1450 °C for 4 h to prepare cemented carbides. With the increase of C/WO3 ratio at the first stage, the content of η-phase with a low melting point increased, which resulted in the large grain size of WC in the finally prepared cemented carbide. Compared with the traditional method of preparing cemented carbides, the cemented carbides prepared by the current method showed a higher hardness and toughness. Furthermore, the addition of a proper content of the VC in the second stage can significantly inhibit the grain growth of WC and further increase the hardness of cemented carbides.

One-step synthesis of ultrafine WC–10Co hardmetals with VC/V 2 O 5 addition by plasma assisted milling

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Properties of WC–8Co Hardmetals with Plate-Like WC Grains Prepared by Plasma-Assisted Milling

Achieving high transverse rupture strength of WC-8Co hardmetals through forming plate-like WC grains by plasma assisted milling

A Novel Method for Direct Synthesis of WC-Co Nanocomposite Powder

Enhancement of the mechanical properties of ultrafine-grained WC-Co cemented carbides via the in-situ generation of VC

Preparation of Ultra-Fine WC-Co Cermet and Its Wear Behavior

A new method of synthesizing ultrafine vanadium carbide by dielectric barrier discharge plasma assisted milling

A short and facile process to synthesize WC-Co cemented carbides

Characterizations of Ball-Milled Nanocrystalline WC–Co Composite Powders and Subsequently Rapid Hot Pressing Sintered Cermets

Rapid synthesis of ultrafine WC-Co cemented carbides by in-situ reactions and spark plasma sintering

Effect of Metal Elements on Microstructure and Mechanical Properties of Ultrafine Cemented Carbide Prepared by SPS

Synergism of Mechanical Milling and Dielectric Barrier Discharge Plasma on the Fabrication of Nano-Powders of Pure Metals and Tungsten Carbide

Microstructure and Mechanical Properties of WC-10wt.%AlCoCrFeNi Cemented Carbides Fabricated by Plasma-Assisted Ball Milling

Enhanced Coarse-Grained WC-Co(Ce) Cemented Carbide Prepared through Co-Precipitation

Performance Enhancement of Ultra-Coarse Cemented Carbide by Boride Additives

Fabrication and Properties of Axisymmetric WC/Co Functionally Graded Hard Metal via Microwave Sintering

Ultrafine grained WC-10FeCoCu cemented carbides doped with La 2 O 3 prepared by spark plasma sintering

Effect of particle size and high-energy ball milling time on microstructure and mechanical properties of WC-10Co cemented carbides with plate-like WC grains

Coprecipitation of co and La 2 O 3 coprecipitation on WC for tailoring the grain distribution and boundary of high-performance coarse-grained WC-10Co cemented carbide

Synthesis and Characterizations of Nanocrystalline Wc-Co Composite Powders by A Unique Ball Milling Process