Abstract:High-temperature superconductor (Re)Ba2Cu3Ox (ReBCO) conductor on round core cable (CORC®) has a large current carrying capacity for high field magnets. Lorentz forces acting on CORC conductors, cause a reduction of the critical current, or even permanent degradation of their performance when exceeding critical values. Transverse compressive stress is one of the principal mechanical stresses when CORC cables are bundled to CICC conductors capable of operating at currents up to 100 kA in magnetic fields of up to 20 T. In this research, a mechanical-electromagnetic model is developed to study the effect of transverse compressive loads on the electromagnetic performance of CORC cables. A mechanical transverse load on the cable is implemented to simulate the electromagnetic force. A comparison of numerical simulations with experiments for a three-layer CORC cable is first performed to validate the model's reliability, with particular attention to critical current reduction during the transverse compression process. A novel feature of this paper is that the model developed can analyze both mechanical response under transverse compressive loads and electromagnetic performance under applied AC magnetic fields with low amplitudes. On this basis, the model investigates the effects of winding parameters on the axial strain and critical current reduction of the ReBCO layer in a single-layer CORC cable. The numerical analysis shows that increasing the winding angle can reduce the axial strain and critical current reduction of the ReBCO layer in the contact area. Subsequently, a detailed comparative study is carried out studying the axial strain of the ReBCO layer in the non-contact area with and without taking the winding core into account. In addition, a sudden increase of the magnetization loss is explained when the transverse compressive load reaches a certain level. Finally, a six-layer CORC cable's electromagnetic analysis is performed, and each tape layer's critical current reduction is investigated and discussed. The comparison of magnetization loss and current density between six- and single-layer CORC cables in the no-strain case is also given. This FE model can guide optimizing a cable design for specific application conditions.

Numerical Study on Simplified Resistive Joints of Coated Conductors: is There a Lower Limit of the Joint Resistance?

An Equivalent Homogenized Model for Non-Superconducting Joints Made by ReBCO Coated Conductors

Numerical Study on Silver Diffusion Joints of Coated Conductors by Finite-Element Method

Numerical Study on Mechanical Behavior and Electromechanical Properties of Solder-Jointed REBCO-Coated Conductors

Critical current degradation of commercial REBCO coated conductors under thermomechanical loads

The Electrical Behavior of Stacked Coated Conductors Concerning the Interlayer Resistance

Three-dimensional simulation of single-lap and bridge joints of coated conductor under tension and bending tests

Field and temperature scaling of the critical current density in commercial REBCO coated conductors

Development of Electromagnetic Forming Nbti Superconducting Joint

Investigating the effect of transverse compressive loads on the electromagnetic performance of superconducting CORC® cables

Experimental study to investigate magnetic field and winding force-dependent contact resistance of NI REBCO coil

The Possible Control Method of Turn-to-Turn Contact Resistivity of REBCO Coil by Surface Coating

Effect of the Cu Stabilisation Layer on the Turn-to-turn Contact Resistance of a Non-Insulated REBCO Winding

Electromagnetic-thermal-structure multi-layer nonlinear elastoplastic modelling study on epoxy-impregnated REBCO pancake coils in high-field magnets

Effects of lateral critical current nonuniformity on stresses in dry-wound high-field REBCO coils

Study of contact resistivity of a no-insulation superconducting coil

Electrical Contact Resistance in REBCO Stacks and Cables With Modified Surfaces

An Advanced Computational Approach for Evaluating Screening-Current-Induced Strain in REBCO HTS Coils Considering Electromagnetic-Mechanical Coupling

Superconducting Characteristics of REBCO Coated Conductors with Different Zr Content

Investigation of Orthogonal Experiment for Fabrication of A Soldering Joint for A 4-T Hts Coil

Design and optimization of low-resistance YBCO superconducting joint