Abstract:The ultra-thin multilayer ceramics capacitors (MLCCs) with layer thickness less than 1 tm are in urgent demand due to the rapid development of modern electronic industries. However, the preparation of the dielectric materials with the desirable grain size <150 nm is a huge challenge. In this work, the ultra-fine BaTiO3 (BT) powders (<120 nm) prepared via solid-state reaction method, hydrothermal method and hydrothermal method following a heat treatment (850 degrees C) are selected to prepare the nano-crystalline non-reducible BT-based ceramics, respectively. The effect of the synthesis methods on the microstructure, electric performance and the reliability of the BT-based ceramics are studied. The results of the Raman, XPS and FT-IR spectroscopy demonstrate that a large number of internal stresses and point defects (hydroxyl/proton defects, Ba vacancies) are existed in the hydrothermal powders and can be eliminated to some extent by a proper heat treatment. Unfortunately, plenty of nano-pores (10-20 nm) are observed in the hydrothermal powders, which cannot be eliminated via the heat treatment or sintering process totally. As a result, the BT-based ceramic prepared by the solid-state powders has an absolute advantage in accelerating aging failure performance, compared to that prepared hydrothermal powders. The TSDC results indicate that the ceramic prepared by the solid-state powders has a lower oxygen vacancy concentration and a higher activation energy. Furthermore, a scaling analysis based on a RC equivalent model identifies the longer oxygen vacancy diffusion time for the ceramic prepared by the solid-state powders. All these features demonstrate that the solid-state ultra-fine BT powders are a promising candidate for the fabrication of the ultra-thin layer MLCCs. (C) 2020 Elsevier B.V. All rights reserved.

Superior Reliability Via Two‐Step Sintering: Barium Titanate Ceramics

Investigation of Improved Reliability in BaTiO3-Based Ceramics Via Two-Step Sintering by Impedance Spectroscopy and Schottky Barrier Model

Improved Energy Storage Performance of Ba0.4Sr0.6TiO3 Nanocrystalline Ceramics Prepared by Using Oxalate Co-Precipitation and Spark Plasma Sintering

Microstructure Evolution and Dielectric Properties of Ultrafine Grained Batio3-Based Ceramics by Two-Step Sintering

Core-shell structure in nanocrystalline modified BaTiO3 dielectric ceramics prepared by different sintering methods

Formation of Core‐Shell Structure in Ultrafine‐Grained BaTiO3‐Based Ceramics Through Nanodopant Method

Influence of Sintering Temperature on Core–shell Structure Evolution and Reliability in Dy Modified BaTiO3 Dielectric Ceramics

Enhanced Dielectric Strength and Energy Storage Density in BaTi 0.7 Zr 0.3 O 3 Ceramics Via Spark Plasma Sintering

Sintering Behavior and Reliability Characteristics of Batio3-Based Ceramics Prepared by Different Methods

Preparation of Nano BaTiO3-Based Dielectric Ceramics by Different Sintering Methods

Significantly Enhanced Dielectric Properties of BaTiO3-based Ceramics Via Synergetic Grain Size and Defect Engineering

Significantly Enhanced Reliability in Defect-Engineered BaTi1-xMgxO3 Ceramics

The Effect of B2o3-Li2co3 Addition on Sintering Behavior and Dielectric Properties of Ba0.6sr0.4tio3 Ceramics

Improving Energy Storage Performance of Barium Titanate-Based Ceramics by Doping MnO2

Bulk dense Ba4Ti13O30 ceramics prepared by mixed-phase two-step sintering method

Exceptional reliability of MLCCs enabled by defect-engineered BaTiO<sub>3</sub>

The Properties of Al2O3 Coated Fine‐grain Temperature Stable BaTiO3‐based Ceramics Sintered in Reducing Atmosphere

Optimization of microstructure and dielectric properties of BCTZ-based ceramics using two-step sintering method

The effects of solid-state and hydrothermal synthesis methods of BaTiO3 on the reliability of multilayer ceramic capacitors

High Reliable Non-Reducible Ultra-Fine BaTiO3-based Ceramics Fabricated Via Solid-State Method

Fabrication of BaTiO 3 nanopowders with high tetragonality via two-step assisted rotary furnace calcination for MLCC applications