Abstract:A developed tungsten (W) grade was prepared by powder metallurgy technology plus multi-step low-temperature rolling. The relative density, thermal conductivity, microstructure, tensile properties of original and high-temperature annealed states, micro-hardness and transient thermal shock resistance were characterized. The results of tensile test with a strain rate of 2 × 10 -4 s -1 show that the ductile-brittle transition temperature (DBTT) of rolled-W in the original and recrystallized state are 150 - 200 °C and 250 - 300 °C, respectively. The rolled-W presents high strength and great plasticity simultaneously. For example, the maximum ultimate tensile strength (UTS) below DBTT is as high as ∼1189 MPa, and the maximum total elongation (TE) above DBTT reaches 28.9%. In particular, the TE of recrystallized W achieves an incredible 81.4% at 500 °C, which is the highest value among all the published literatures so far. The results of transient thermal shock tests indicate that the rolled-W has an outstanding transient thermal shock resistance. It can withstand the thermal bombardment at an absorbed power densities (APD) of 0.33 GW·m -2 without causing any surface damages, and still no cracks are observed as the APD rises to 0.88 GW·m -2 . Moreover, the failure mechanism of rolled-W was also studied in details. This work plays an important role in establishing a dependable China Fusion Engineering Test Reactor (CFETR) data-library on a unitary W grade, which can provide an effective reference for the identification of material performance under the high heat flux and subsequent numerical simulation.

High Thermal Shock Resistance of the Hot Rolled and Swaged Bulk W–ZrC Alloys

Effects of ZrC Content on the Mechanical Properties and Microstructures of Hot-Rolled W–ZrC Composites

Fabrication and Stability of Ultrafine ZrC Nanoparticles Dispersion Strengthened Sub-Micrometer Grained W Alloy

Effects of Rolling Reduction on Microstructural Evolution and Mechanical Properties of W-0.5wt%ZrC Alloys

Tensile fracture behavior and texture evolution of a hot-rolled W-Y<sub>2</sub>(Zr)O<sub>3</sub> alloy

Mechanical Properties and Thermal Stability of W-ZrC/HfC-Re Alloys Fabricated by Spark Plasma Sintering

The High Thermal Stability Induced by a Synergistic Effect of ZrC Nanoparticles and Re Solution in W Matrix in Hot Rolled Tungsten Alloy

Anisotropy and stability of the mechanical properties of the W alloy plate reinforced with Y-Zr-O particles and prepared by a wet chemical method

Tensile fracture behavior and texture evolution of a hot-rolled W–Y2(Zr)O3 alloy

High-temperature tensile and thermal shock characterization of low-temperature rolled tungsten

Enhanced Mechanical Properties and Thermal Stability of Hot-Rolled Mo-0.5%ZrC Alloy

Effect of rotary swaging and subsequent annealing on microstructure and mechanical properties of W-1.5ZrO2 alloys

Thermal Shock Resistance of Nanocrystalline and Ultrafine-Grained W-Y2O3-Ti Alloys

Room temperature ductile W-Y2O3 alloy with high thermal shock resistance

Mechanical properties and thermal shock behavior of hot-pressed ZrB2–SiC–AlN composites

Influence of Zr on grain orientation, texture, and mechanical properties in hot- and warm-rolled FeCrAl alloys

Enhanced thermal-mechanical properties of rolled tungsten bulk material reinforced by in situ nanosized Y–Zr–O particles

Transient thermal shock behavior of W–Zr/Sc2O3 composites prepared via spark plasma sintering

Isotropic Thermal Conductivity in Rolled Large-Sized W-Y2O3 Bulk Material Prepared by Powder Metallurgy Route and Rolling Deformation Technology

Microstructure evolution of W-1.0 m-ZrO2 alloy during high temperature deformation

Microstructure and Mechanical Properties of In-Situ Formed ZrC Nanoparticles Dispersion-Strengthened Tungsten Alloy