Abstract:The high-temperature deformation and fracture behavior of molybdenum/partially stabilized zirconia composites prepared by powder metallurgical route, was evaluated up to 1573 K by means of modified small punch test (MSP), which had been originally designed for the evaluation of brittle to ductile transition in metallic materials used for nuclear applications. For the design of thermal barrier type of functionally graded materials, along with the thermomechanical properties in full compositional range, a special attention must be paid for evaluating the transition behavior of deformation and fracture with temperatures because of definite contribution of inelasticity of materials under thermal loading to the failure often observed during cooling. The results of the dependence of MSP load-deflection curve on temperature have shown apparent transitions in the deformation and fracture of the composites: that is, every composite, which is brittle at room temperature, turns into ductile above a certain critical temperature and shows the similar load-deflection curve to those obtained in the case of ductile metallic materials. The brittle to ductile transition temperature which corresponds to the critical temperature was determined accurately by analyzing the temperature dependence of MSP-energy which was figured out as the area below each load-deflection curve. It has been found that the transition temperature is susceptible to the sintered microstructure, where the variation in transition temperature can be more closely related to the continuity of constituent phases rather than the nominal composition. The brittle to ductile transition behavior has been shown to be dependent not only on the temperature but also on the composition, which was quantitatively represented in an MSP-energy transition map.

Transient thermal shock behavior of W–Zr/Sc2O3 composites prepared via spark plasma sintering

Thermal shock behavior of W–ZrC/Sc2O3 composites under two different transient events by electron and laser irradiation

Mechanical Properties and Thermal Shock Performance of W-Y2O3composite Prepared by High-Energy-rate Forging

Influence of Zrc Content on the Elevated Temperature Tensile Properties of Zrcp/W Composites

Investigation of W–B Behavior During Short Transient Events by Laser Irradiation

Microstructure and Transient Laser Thermal Shock Behavior of W–TiC–Y2O3 Composites Prepared by Wet Chemical Method

Effects of Zirconium Element on the Microstructure and Deuterium Retention of W–Zr/Sc2O3 Composites

Microstructure and Properties of W/Sm2O3 Composites Prepared Spark Plasma Sintering

Surface Cracking of Tungsten-Vanadium Alloys under Transient Heat Loads

High Temperature Deformation and Fracture Behavior in Sintered Mo/PSZ Composites As Evaluated by Small Punch Test

Design and characterization of therm-al shock resistance of several typical zirconia reinforced alumina ceramic composites

Surface Damage Evolution During Transient Thermal Shock of W-2%vol Y2O3 Composite Material in Different Surfaces

The superior thermal stability and irradiation resistance capacities of tungsten composites synthesized by simple second-phase particle component modulation

Evaluating surface damage behavior of W-(Y0.9La0.1)2O3 composites during spark plasma sintering process improvement

Enhanced thermal shock resistance of ZrO2-reinforced Al2O3–CaAl12O19 composites prepared from ferrotitanium slag: Crack propagation resistance mechanisms

Preparation and laser shock resistance of W/Si composites

Surface Damage During Transient Thermal Load of 50% Thickness Reduced W-2% (vol.) Y2O3 Sheet with Different Recrystallization Volume Fraction

Densification and microstructure evolution of W-TiC-Y2O3 during spark plasma sintering

Thermal Shock Behavior of W-0.5 Wt% Y 2 O 3 Alloy Prepared Via a Novel Chemical Method

Novel low temperature derived W f /W-ZrC-Cu composites by reactive infiltration with enhanced mechanical and thermal physical properties

Microstructure and Helium Irradiation Performance of W–ZrC/Sc 2 O 3 Composites Prepared Spark Plasma Sintering