Abstract:In situ compressive behavior of carbon fibers reinforced PPS laminates. This study investigates the influence of a combined thermal heat flux (imposed by a cone calorimeter) and a compressive loading on the deformation and damage mechanisms within quasi‐isotropic carbon fibers reinforced thermoplastic (polyetherether ketone [PEEK] and polyphenylene sulfide [PPS]) and thermosetting (epoxy) laminates. First, thermogravimetric Analyses conducted under nitrogen provide valuable information on the thermal decomposition of these materials depending on the matrix nature (580–510°C and 350°C, respectively) which is a key factor to explain the mechanical behavior under fire conditions. Second, under the same testing conditions (creep loading under a 50 kW/m2 heat flux), the time to failure is about 17 times as high (C/PEEK), twice as high (C/PPS) with respect to C/epoxy laminates. At the ply scale, the exposure of thermoplastic matrices (PEEK and PPS) to a 50 kW/m2 heat flux causes softening and thermal decomposition, facilitating the micro‐buckling of fiber bundles in matrix‐rich areas. At the laminates scale, this mechanism ultimately leads to the formation and propagation of plastic kink bands in the transverse direction. In epoxy‐based laminates, the onset of matrix pyrolysis occurs at lower temperatures (350°C) during thermal aggression, and thermal decomposition has started in all the plies of the laminates. Combined with the low ductility of the epoxy matrix, the compressive response is elastic‐brittle and results from the buckling of 0° plies outside the thermally‐damaged area. Highlights Study on the compression of polymer composites exposed to a 50 kW/m2 heat flux. The influence of the matrix nature (thermoplastic vs thermoset) is discussed. Time to failure is about 17 times higher in C/PEEK compared to C/Epoxy. Plastic kink bands propagate in thermoplastic composites at T > Tg. C/Epoxy laminates undergo buckling outside the thermally damaged area.

High-temperature Damage Tolerance of Carbon Fibre-Reinforced Plastics

Comparison of the in situ compressive behavior of carbon fibers woven ply laminates exposed to one‐sided heat flux: Thermoplastic versus thermosetting composites

Influence of Temperature on the Impact Behavior of Woven-Ply Carbon Fiber Reinforced Thermoplastic Composites

Effect of Thermal Ageing on the Impact Damage Resistance and Tolerance of Carbon-Fibre-Reinforced Epoxy Laminates

Effects of high temperature and strain rate on the impact-induced inter-laminar shear behavior of plain woven CF/PEEK thermoplastic composites

Transverse impacts‐induced deformation and damage of 3D angle‐interlock woven composites at elevated temperatures

Experimental investigation on low‐velocity impact performance of carbon fiber reinforced polyether ether ketone thermoplastic composite materials in room and elevated temperature

About the influence of high temperature or fire testing conditions on the tensile behavior of carbon reinforced poly phenylene sulfide laminates

Mechanical Property Evolution and Life Prediction of Carbon Fiber and Pultruded Carbon Fiber Reinforced Polymer Plate Exposed to Elevated Temperatures

A comprehensive study of low-velocity impact behavior and damage evaluation of angle-ply thin woven GFRP composites under various temperatures

Mechanical Properties of High-Temperature Fiber-Reinforced Thermoset Composites with Plain Weave and Unidirectional Carbon Fiber Fillers

Effects of temperature and strain rate on impact compression behaviors of three-dimensional carbon fiber/epoxy braided composites

The behaviour of thermoplastic and thermoset carbon fibre composites subjected to low-velocity and high-velocity impact

Residual bending strength after impact of CFRP laminates in hygrothermal condition

Combined Effects of Sustained Tensile Loading and Elevated Temperatures on the Mechanical Properties of Pultruded BFRP Plates

The influence of temperature and moisture on the mode I fracture toughness and associated fracture morphology of a highly toughened aerospace CFRP

Thermomechanical Behavior and Microstructure Properties of Carbon Fiber Reinforced Polymer at Elevated Temperatures

In situ interlaminar shear behavior of carbon fibers reinforced polymer composites exposed to severe thermal aggressions: PPS versus epoxy laminates

High performance thermoplastic polymer for the compressive behaviour of carbon fibre reinforced composites

Flexural Fatigue Behavior of a Pultruded Basalt Fiber Reinforced Epoxy Plate Subjected to Elevated Temperatures Exposure

Impact Damage Tolerance of Thermoset Composites Reinforced with Hybrid Commingled Yarns