Abstract:The investigation on geopolymers has intrigued broad interests in the past decades, due to the requirements for the recycling of aluminosilicate solid wastes, such as red mud, slags, sludges and demolished concrete. Previous studies have demonstrated the feasibility of reusing this Aluminosilicate as a resource to prepare cementitious materials and indicated their promising properties at ambient temperature. However, when this material was exposed to high temperatures, especially above 1000 °C, the microstructure evolution mechanisms were not systematically investigated. In this study, the microstructural evolution process of metakaolin-based K geopolymer (molar ratio of K:Al:Si was 1:1:4) is investigated. The crystalized leucite originated from the geopolymer precursor was detected above 1000 °C. The SEM results indicate that the microstructure of the geopolymer before heating was composed of non-reacted metakaolin with a typical layered structure and reacted amorphous binder phase. As the geopolymer heated to 1000 °C, the microstructure of the geopolymer changed to a porous structure with an average pore size from 10 to 30 μm. When the heating temperature reached 1100 °C, the pores started to close along with the leucite crystallization process. As the heating temperature reached 1200 °C, most of the pores were closed. The TEM results show that the microstructure of the geopolymer, after being heated to 1400 °C, was composed of an amorphous glassy phase and crystallized leucite phase. The crystallized leucite grains originated from the nano-sized crystal nuclei, with an average size of 2–3 nm. The TEM-EDS results indicate that the chemical composition of the glassy phase was complicated. It varied from area to area because of the movement and uneven distribution of K.

Preparation of fully stabilized cubic-leucite composite through heat-treating Cs-substituted K-geopolymer composite at high temperatures

Preparation and in-situ high-temperature mechanical properties of Cf-SiCf reinforced geopolymer composites

Effects of high-temperature heat treatment on the microstructure and mechanical performance of hybrid Cf-SiCf-(Al2O3p) reinforced geopolymer composites

High temperature in-situ synchrotron-based XRD study on the crystal structure evolution of C/C composite impregnated by FLiNaK molten salt

Preparation and characterization of Cf/Pollucite composites through geopolymer precursors

Effect of high temperature heating on the microstructure and performance of cesium-based geopolymer reinforced by cordierite

Improvement of High-Temperature Mechanical Properties of Heat Treated Cf/geopolymer Composites by Sol-SiO2 Impregnation

Effects of high-temperature heat treatment on the mechanical properties of unidirectional carbon fiber reinforced geopolymer composites

In situ processing of MWCNTs/leucite composites through geopolymer precursor

Interface evolution of the Cf/leucite composites derived from Cf/geopolymer composites

In-situ preparation of fully stabilized graphene/cubic-leucite composite through graphene oxide/geopolymer

Microstructure Evolution Mechanism of Geopolymers with Exposure to High-Temperature Environment

Thermal Evolution of Lithium Ion Substituted Cesium-Based Geopolymer under High Temperature Treatment, Part I: Effects of Holding Temperature

Effect of Heat Treatment on Mechanical Properties of Unidirectional Carbon Fiber Reinforced Geopolymer Composites

Thermal-mechanical Properties of Short Carbon Fiber Reinforced Geopolymer Matrix Composites Subjected to Thermal Load

Microstructure and Integrity of Leucite Ceramic Derived from Potassium-Based Geopolymer Precursor

Effect of High Temperature on the Mechanical Properties of Hierarchical Porous Cenosphere/geopolymer Composite Foams

Preparation of eco-friendly porous ceramic with low thermal conductivity by high-temperature treatment of foamed solid waste based geopolymer with cenospheres

Using PyC modified 3D carbon fiber to reinforce UHTC under low temperature sintering without pressure

Effect of cesium substitution on the thermal evolution and ceramics formation of potassium-based geopolymer

Effect of High Temperature Heat Treatment on Mechanical Property of Cr-Geopolymer Composite